[ECU] – DTC Fault Code

P0100 Hot-film mass-air sensor ME-SFI
P0100 Mass or Volume Air Flow Circuit Malfunction
P0101 Mass or Volume Air Flow Circuit Range/Performance Problem
P0102 Mass or Volume Air Flow Circuit Low Input
P0103 Mass or Volume Air Flow Circuit High Input
P0104 Mass or Volume Air Flow Circuit Intermittent
P0105 Manifold Absolute Pressure/Barometric Pressure Circuit Malfunction
P0106 Manifold Absolute Pressure/Barometric Pressure Circuit Range/Performance Problem
P0106 Pressure sensor ME-SFI Intake manifold pressure
P0107 Manifold Absolute Pressure/Barometric Pressure Circuit Low Input
P0108 Manifold Absolute Pressure/Barometric Pressure Circuit High Input
P0109 Intake Air Temperature Circuit Malfunction
P0109 Manifold Absolute Pressure/Barometric Pressure Circuit Intermittent
P0111 Intake Air Temperature Circuit Range/Performance Problem
P0112 Intake Air Temperature Circuit Low Input
P0113 Intake Air Temperature Circuit High Input
P0114 Intake Air Temperature Circuit Intermittent
P0115 Engine Coolant Temperature Circuit Malfunction
P0116 Engine Coolant Temperature Circuit Range/Performance Problem
P0117 Engine Coolant Temperature Circuit Low Input
P0118 Engine Coolant Temperature Circuit High Input
P0119 Engine Coolant Temperature Circuit Intermittent
P0120 Throttle/Petal Position Sensor/Switch A Circuit Malfunction
P0121 Throttle/Petal Position Sensor/Switch A Circuit Range/Performance Problem
P0122 Throttle/Petal Position Sensor/Switch A Circuit Low Input
P0123 Throttle/Petal Position Sensor/Switch A Circuit High Input
P0124 Throttle/Petal Position Sensor/Switch A Circuit Intermittent
P0125 Insufficient Coolant Temperature for Closed Loop Fuel Control
P0126 Insufficient Coolant Temperature for Stable Operation
P0130 O2 Sensor Circuit Malfunction (Bank 1 Sensor 1)
P0131 O2 Sensor Circuit Low Voltage (Bank 1 Sensor 1)
P0132 O2 Sensor Circuit High Voltage (Bank 1 Sensor 1)
P0133 O2 Sensor Circuit Slow Response (Bank 1 Sensor 1)
P0134 O2 Sensor Circuit No Activity Detected (Bank 1 Sensor 1)
P0135 O2 Sensor Heater Circuit Malfunction (Bank 1 Sensor 1)
P0136 O2 Sensor Circuit Malfunction (Bank 1 Sensor 2)
P0137 O2 Sensor Circuit Low Voltage (Bank 1 Sensor 2)
P0138 O2 Sensor Circuit High Voltage (Bank 1 Sensor 2)
P0139 O2 Sensor Circuit Slow Response (Bank 1 Sensor 2)
P0140 O2 Sensor Circuit No Activity Detected (Bank 1 Sensor 2)
P0141 O2 Sensor Heater Circuit Malfunction (Bank 1 Sensor 2)
P0142 O2 Sensor Circuit Malfunction (Bank 1 Sensor 3)
P0143 O2 Sensor Circuit Low Voltage (Bank 1 Sensor 3)
P0144 O2 Sensor Circuit High Voltage (Bank 1 Sensor 3)
P0145 O2 Sensor Circuit Slow Response (Bank 1 Sensor 3)
P0146 O2 Sensor Circuit No Activity Detected (Bank 1 Sensor 3)
P0147 O2 Sensor Heater Circuit Malfunction (Bank 1 Sensor 3)
P0150 O2 Sensor Circuit Malfunction (Bank 2 Sensor 1)
P0151 O2 Sensor Circuit Low Voltage (Bank 2 Sensor 1)
P0152 O2 Sensor Circuit High Voltage (Bank 2 Sensor 1)
P0153 O2 Sensor Circuit Slow Response (Bank 2 Sensor 1)
P0154 O2 Sensor Circuit No Activity Detected (Bank 2 Sensor 1)
P0155 O2 Sensor Heater Circuit Malfunction (Bank 2 Sensor 1)
P0156 O2 Sensor Circuit Malfunction (Bank 2 Sensor 2)
P0157 O2 Sensor Circuit Low Voltage (Bank 2 Sensor 2)
P0158 O2 Sensor Circuit High Voltage (Bank 2 Sensor 2)
P0159 O2 Sensor Circuit Slow Response (Bank 2 Sensor 2)
P0160 O2 Sensor Circuit No Activity Detected (Bank 2 Sensor 2)
P0161 O2 Sensor Heater Circuit Malfunction (Bank 2 Sensor 2)
P0162 O2 Sensor Circuit Malfunction (Bank 2 Sensor 3)
P0163 O2 Sensor Circuit Low Voltage (Bank 2 Sensor 3)
P0164 O2 Sensor Circuit High Voltage (Bank 2 Sensor 3)
P0165 O2 Sensor Circuit Slow Response (Bank 2 Sensor 3)
P0166 O2 Sensor Circuit No Activity Detected (Bank 2 Sensor 3)
P0167 O2 Sensor Heater Circuit Malfunction (Bank 2 Sensor 3)
P0170 Fuel Trim Malfunctio

P0100 Hot-film mass-air sensor ME-SFI
P0100 Mass or Volume Air Flow Circuit Malfunction
P0101 Mass or Volume Air Flow Circuit Range/Performance Problem
P0102 Mass or Volume Air Flow Circuit Low Input
P0103 Mass or Volume Air Flow Circuit High Input
P0104 Mass or Volume Air Flow Circuit Intermittent
P0105 Manifold Absolute Pressure/Barometric Pressure Circuit Malfunction
P0106 Manifold Absolute Pressure/Barometric Pressure Circuit Range/Performance Problem
P0106 Pressure sensor ME-SFI Intake manifold pressure
P0107 Manifold Absolute Pressure/Barometric Pressure Circuit Low Input
P0108 Manifold Absolute Pressure/Barometric Pressure Circuit High Input
P0109 Intake Air Temperature Circuit Malfunction
P0109 Manifold Absolute Pressure/Barometric Pressure Circuit Intermittent
P0111 Intake Air Temperature Circuit Range/Performance Problem
P0112 Intake Air Temperature Circuit Low Input
P0113 Intake Air Temperature Circuit High Input
P0114 Intake Air Temperature Circuit Intermittent
P0115 Engine Coolant Temperature Circuit Malfunction
P0116 Engine Coolant Temperature Circuit Range/Performance Problem
P0117 Engine Coolant Temperature Circuit Low Input
P0118 Engine Coolant Temperature Circuit High Input
P0119 Engine Coolant Temperature Circuit Intermittent
P0120 Throttle/Petal Position Sensor/Switch A Circuit Malfunction
P0121 Throttle/Petal Position Sensor/Switch A Circuit Range/Performance Problem
P0122 Throttle/Petal Position Sensor/Switch A Circuit Low Input
P0123 Throttle/Petal Position Sensor/Switch A Circuit High Input
P0124 Throttle/Petal Position Sensor/Switch A Circuit Intermittent
P0125 Insufficient Coolant Temperature for Closed Loop Fuel Control
P0126 Insufficient Coolant Temperature for Stable Operation
P0130 O2 Sensor Circuit Malfunction (Bank 1 Sensor 1)
P0131 O2 Sensor Circuit Low Voltage (Bank 1 Sensor 1)
P0132 O2 Sensor Circuit High Voltage (Bank 1 Sensor 1)
P0133 O2 Sensor Circuit Slow Response (Bank 1 Sensor 1)
P0134 O2 Sensor Circuit No Activity Detected (Bank 1 Sensor 1)
P0135 O2 Sensor Heater Circuit Malfunction (Bank 1 Sensor 1)
P0136 O2 Sensor Circuit Malfunction (Bank 1 Sensor 2)
P0137 O2 Sensor Circuit Low Voltage (Bank 1 Sensor 2)
P0138 O2 Sensor Circuit High Voltage (Bank 1 Sensor 2)
P0139 O2 Sensor Circuit Slow Response (Bank 1 Sensor 2)
P0140 O2 Sensor Circuit No Activity Detected (Bank 1 Sensor 2)
P0141 O2 Sensor Heater Circuit Malfunction (Bank 1 Sensor 2)
P0142 O2 Sensor Circuit Malfunction (Bank 1 Sensor 3)
P0143 O2 Sensor Circuit Low Voltage (Bank 1 Sensor 3)
P0144 O2 Sensor Circuit High Voltage (Bank 1 Sensor 3)
P0145 O2 Sensor Circuit Slow Response (Bank 1 Sensor 3)
P0146 O2 Sensor Circuit No Activity Detected (Bank 1 Sensor 3)
P0147 O2 Sensor Heater Circuit Malfunction (Bank 1 Sensor 3)
P0150 O2 Sensor Circuit Malfunction (Bank 2 Sensor 1)
P0151 O2 Sensor Circuit Low Voltage (Bank 2 Sensor 1)
P0152 O2 Sensor Circuit High Voltage (Bank 2 Sensor 1)
P0153 O2 Sensor Circuit Slow Response (Bank 2 Sensor 1)
P0154 O2 Sensor Circuit No Activity Detected (Bank 2 Sensor 1)
P0155 O2 Sensor Heater Circuit Malfunction (Bank 2 Sensor 1)
P0156 O2 Sensor Circuit Malfunction (Bank 2 Sensor 2)
P0157 O2 Sensor Circuit Low Voltage (Bank 2 Sensor 2)
P0158 O2 Sensor Circuit High Voltage (Bank 2 Sensor 2)
P0159 O2 Sensor Circuit Slow Response (Bank 2 Sensor 2)
P0160 O2 Sensor Circuit No Activity Detected (Bank 2 Sensor 2)
P0161 O2 Sensor Heater Circuit Malfunction (Bank 2 Sensor 2)
P0162 O2 Sensor Circuit Malfunction (Bank 2 Sensor 3)
P0163 O2 Sensor Circuit Low Voltage (Bank 2 Sensor 3)
P0164 O2 Sensor Circuit High Voltage (Bank 2 Sensor 3)
P0165 O2 Sensor Circuit Slow Response (Bank 2 Sensor 3)
P0166 O2 Sensor Circuit No Activity Detected (Bank 2 Sensor 3)
P0167 O2 Sensor Heater Circuit Malfunction (Bank 2 Sensor 3)
P0170 Fuel Trim Malfunction (Bank 1) ) check vaccum leaks first or
P0171 System too Lean (Bank 1) ) faulty air mass flow sensor
P0172 System too Rich (Bank 1) )
P0173 Fuel Trim Malfunction (Bank 2) )
P0174 System too Lean (Bank 2) )
P0175 System too Rich (Bank 2) )
P0176 Fuel Composition Sensor Circuit Malfunction
P0177 Fuel Composition Sensor Circuit Range/Performance
P0178 Fuel Composition Sensor Circuit Low Input
P0179 Fuel Composition Sensor Circuit High Input
P0180 Fuel Temperature Sensor A Circuit Malfunction
P0181 Fuel Temperature Sensor A Circuit Range/Performance
P0182 Fuel Temperature Sensor A Circuit Low Input
P0183 Fuel Temperature Sensor A Circuit High Input
P0184 Fuel Temperature Sensor A Circuit Intermittent
P0185 Fuel Temperature Sensor B Circuit Malfunction
P0186 Fuel Temperature Sensor B Circuit Range/Performance
P0187 Fuel Temperature Sensor B Circuit Low Input
P0188 Fuel Temperature Sensor B Circuit High Input
P0189 Fuel Temperature Sensor B Circuit Intermittent
P0190 Fuel Rail Pressure Sensor Circuit Malfunction
P0191 Fuel Rail Pressure Sensor Circuit Range/Performance
P0192 Fuel Rail Pressure Sensor Circuit Low Input
P0193 Fuel Rail Pressure Sensor Circuit High Input
P0194 Fuel Rail Pressure Sensor Circuit Intermittent
P0195 Engine Oil Temperature Sensor Malfunction
P0196 Engine Oil Temperature Sensor Range/Performance
P0197 Engine Oil Temperature Sensor Low
P0198 Engine Oil Temperature Sensor High
P0199 Engine Oil Temperature Sensor Intermittent
P0200 Injector Circuit Malfunction
P0201 Injector Circuit Malfunction – Cylinder 1
P0202 Injector Circuit Malfunction – Cylinder 2
P0203 Injector Circuit Malfunction – Cylinder 3
P0204 Injector Circuit Malfunction – Cylinder 4
P0205 Injector Circuit Malfunction – Cylinder 5
P0206 Injector Circuit Malfunction – Cylinder 6
P0207 Injector Circuit Malfunction – Cylinder 7
P0208 Injector Circuit Malfunction – Cylinder 8
P0209 Injector Circuit Malfunction – Cylinder 9
P0210 Injector Circuit Malfunction – Cylinder 10
P0211 Injector Circuit Malfunction – Cylinder 11
P0212 Injector Circuit Malfunction – Cylinder 12
P0213 Cold Start Injector 1 Malfunction
P0214 Cold Start Injector 2 Malfunction
P0215 Engine Shutoff Solenoid Malfunction
P0216 Injection Timing Control Circuit Malfunction
P0217 Engine Overtemp Condition
P0218 Transmission Over Temperature Condition
P0219 Engine Overspeed Condition
P0220 Throttle/Petal Position Sensor/Switch B Circuit Malfunction
P0221 Throttle/Petal Position Sensor/Switch B Circuit Range/Performance Problem
P0222 Throttle/Petal Position Sensor/Switch B Circuit Low Input
P0223 Throttle/Petal Position Sensor/Switch B Circuit High Input
P0224 Throttle/Petal Position Sensor/Switch B Circuit Intermittent
P0225 Throttle/Petal Position Sensor/Switch C Circuit Malfunction
P0226 Throttle/Petal Position Sensor/Switch C Circuit Range/Performance Problem
P0227 Throttle/Petal Position Sensor/Switch C Circuit Low Input
P0228 Throttle/Petal Position Sensor/Switch C Circuit High Input
P0229 Throttle/Petal Position Sensor/Switch C Circuit Intermittent
P0230 Fuel Pump Primary Circuit Malfunction
P0231 Fuel Pump Secondary Circuit Low
P0232 Fuel Pump Secondary Circuit High
P0233 Fuel Pump Secondary Circuit Intermittent
P0234 Engine Overboost Condition
P0235 Turbocharger Boost Sensor A Circuit Malfunction
P0236 Turbocharger Boost Sensor A Circuit Range/Performance
P0237 Turbocharger Boost Sensor A Circuit Low
P0238 Turbocharger Boost Sensor A Circuit High
P0239 Turbocharger Boost Sensor B Malfunction
P0240 Turbocharger Boost Sensor B Circuit Range/Performance
P0241 Turbocharger Boost Sensor B Circuit Low
P0242 Turbocharger Boost Sensor B Circuit High
P0243 Turbocharger Wastegate Solenoid A Malfunction
P0244 Turbocharger Wastegate Solenoid A Range/Performance
P0245 Turbocharger Wastegate Solenoid A Low
P0246 Turbocharger Wastegate Solenoid A High
P0247 Turbocharger Wastegate Solenoid B Malfunction
P0248 Turbocharger Wastegate Solenoid B Range/Performance
P0249 Turbocharger Wastegate Solenoid B Low
P0250 Turbocharger Wastegate Solenoid B High
P0251 Injection Pump Fuel Metering Control “A” Malfunction (Cam/Rotor/Injector)
P0252 Injection Pump Fuel Metering Control “A” Range/Performance (Cam/Rotor/Injector)
P0253 Injection Pump Fuel Metering Control “A” Low (Cam/Rotor/Injector)
P0254 Injection Pump Fuel Metering Control “A” High (Cam/Rotor/Injector)
P0255 Injection Pump Fuel Metering Control “A” Intermittent (Cam/Rotor/Injector)
P0256 Injection Pump Fuel Metering Control “B” Malfunction (Cam/Rotor/Injector)
P0257 Injection Pump Fuel Metering Control “B” Range/Performance (Cam/Rotor/Injector)
P0258 Injection Pump Fuel Metering Control “B” Low (Cam/Rotor/Injector)
P0259 Injection Pump Fuel Metering Control “B” High (Cam/Rotor/Injector)
P0260 Injection Pump Fuel Metering Control “B” Intermittent (Cam/Rotor/Injector)
P0261 Cylinder 1 Injector Circuit Low
P0262 Cylinder 1 Injector Circuit High
P0263 Cylinder 1 Contribution/Balance Fault
P0264 Cylinder 2 Injector Circuit Low
P0265 Cylinder 2 Injector Circuit High
P0266 Cylinder 2 Contribution/Balance Fault
P0267 Cylinder 3 Injector Circuit Low
P0268 Cylinder 3 Injector Circuit High
P0269 Cylinder 3 Contribution/Balance Fault
P0270 Cylinder 4 Injector Circuit Low
P0271 Cylinder 4 Injector Circuit High
P0272 Cylinder 4 Contribution/Balance Fault
P0273 Cylinder 5 Injector Circuit Low
P0274 Cylinder 5 Injector Circuit High
P0275 Cylinder 5 Contribution/Balance Fault
P0276 Cylinder 6 Injector Circuit Low
P0277 Cylinder 6 Injector Circuit High
P0278 Cylinder 6 Contribution/Balance Fault
P0279 Cylinder 7 Injector Circuit Low
P0280 Cylinder 7 Injector Circuit High
P0281 Cylinder 7 Contribution/Balance Fault
P0282 Cylinder 8 Injector Circuit Low
P0283 Cylinder 8 Injector Circuit High
P0284 Cylinder 8 Contribution/Balance Fault
P0285 Cylinder 9 Injector Circuit Low
P0286 Cylinder 9 Injector Circuit High
P0287 Cylinder 9 Contribution/Balance Fault
P0288 Cylinder 10 Injector Circuit Low
P0289 Cylinder 10 Injector Circuit High
P0290 Cylinder 10 Contribution/Balance Fault
P0291 Cylinder 11 Injector Circuit Low
P0292 Cylinder 11 Injector Circuit High
P0293 Cylinder 11 Contribution/Balance Fault
P0294 Cylinder 12 Injector Circuit Low
P0295 Cylinder 12 Injector Circuit High
P0296 Cylinder 12 Contribution/Range Fault
P0300 Random/Multiple Cylinder Misfire Detected
P0301 Cylinder 1 Misfire Detected
P0302 Cylinder 2 Misfire Detected
P0303 Cylinder 3 Misfire Detected
P0304 Cylinder 4 Misfire Detected
P0305 Cylinder 5 Misfire Detected
P0306 Cylinder 6 Misfire Detected
P0307 Cylinder 7 Misfire Detected
P0308 Cylinder 8 Misfire Detected
P0309 Cylinder 9 Misfire Detected
P0311 Cylinder 11 Misfire Detected
P0312 Cylinder 12 Misfire Detected
P0320 Ignition/Distributor Engine Speed Input Circuit Malfunction
P0321 Ignition/Distributor Engine Speed Input Circuit Range/Performance
P0322 Ignition/Distributor Engine Speed Input Circuit No Signal
P0323 Ignition/Distributor Engine Speed Input Circuit Intermittent
P0325 Knock Sensor 1 Circuit Malfunction (Bank 1 or Single Sensor)
P0326 Knock Sensor 1 Circuit Range/Performance (Bank 1 or Single Sensor)
P0327 Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor)
P0328 Knock Sensor 1 Circuit High Input (Bank 1 or Single Sensor)
P0329 Knock Sensor 1 Circuit Intermittent (Bank 1 or Single Sensor)
P0330 Knock Sensor 2 Circuit Malfunction (Bank 2)
P0331 Knock Sensor 2 Circuit Range/Performance (Bank 2)
P0332 Knock Sensor 2 Circuit Low Input (Bank 2)
P0333 Knock Sensor 2 Circuit High Input (Bank 2)
P0334 Knock Sensor 2 Circuit Intermittent (Bank 2)
P0335 Crankshaft Position Sensor A Circuit Malfunction (L5)
P0336 Crankshaft Position Sensor A Circuit Range/Performance
P0337 Crankshaft Position Sensor A Circuit Low Input
P0338 Crankshaft Position Sensor A Circuit High Input
P0339 Crankshaft Position Sensor A Circuit Intermittent
P0340 Camshaft Position Sensor Circuit Malfunction
P0341 Camshaft Position Sensor Circuit Range/Performance
P0342 Camshaft Position Sensor Circuit Low Input
P0343 Camshaft Position Sensor Circuit High Input
P0344 Camshaft Position Sensor Circuit Intermittent
P0350 Ignition Coil Primary/Secondary Circuit Malfunction
P0351 Ignition Coil A Primary/Secondary Circuit Malfunction
P0352 Ignition Coil B Primary/Secondary Circuit Malfunction
P0353 Ignition Coil C Primary/Secondary Circuit Malfunction
P0354 Ignition Coil D Primary/Secondary Circuit Malfunction
P0355 Ignition Coil E Primary/Secondary Circuit Malfunction
P0356 Ignition Coil F Primary/Secondary Circuit Malfunction
P0357 Ignition Coil G Primary/Secondary Circuit Malfunction
P0358 Ignition Coil H Primary/Secondary Circuit Malfunction
P0359 Ignition Coil I Primary/Secondary Circuit Malfunction
P0360 Ignition Coil J Primary/Secondary Circuit Malfunction
P0361 Ignition Coil K Primary/Secondary Circuit Malfunction
P0362 Ignition Coil L Primary/Secondary Circuit Malfunction
P0370 Timing Reference High Resolution Signal A Malfunction
P0371 Timing Reference High Resolution Signal A Too Many Pulses
P0372 Timing Reference High Resolution Signal A Too Few Pulses
P0373 Timing Reference High Resolution Signal A Intermittent/Erratic Pulses
P0374 Timing Reference High Resolution Signal A No Pulses
P0375 Timing Reference High Resolution Signal B Malfunction
P0376 Timing Reference High Resolution Signal B Too Many Pulses
P0377 Timing Reference High Resolution Signal B Too Few Pulses
P0378 Timing Reference High Resolution Signal B Intermittent/Erratic Pulses
P0379 Timing Reference High Resolution Signal B No Pulses
P0380 Glow Plug/Heater Circuit “A” Malfunction
P0381 Glow Plug/Heater Indicator Circuit Malfunction
P0382 Exhaust Gas Recirculation Flow Malfunction
P0385 Crankshaft Position Sensor B Circuit Malfunction
P0386 Crankshaft Position Sensor B Circuit Range/Performance
P0387 Crankshaft Position Sensor B Circuit Low Input
P0388 Crankshaft Position Sensor B Circuit High Input
P0389 Crankshaft Position Sensor B Circuit Intermittent
P0400 Exhaust Gas Recirculation Flow Malfunction
P0401 Exhaust Gas Recirculation Flow Insufficient Detected
P0402 Exhaust Gas Recirculation Flow Excessive Detected
P0403 Exhaust Gas Recirculation Circuit Malfunction
P0404 Exhaust Gas Recirculation Circuit Range/Performance
P0405 Exhaust Gas Recirculation Sensor A Circuit Low
P0406 Exhaust Gas Recirculation Sensor A Circuit High
P0407 Exhaust Gas Recirculation Sensor B Circuit Low
P0408 Exhaust Gas Recirculation Sensor B Circuit High
P0410 Secondary Air Injection System Malfunction
P0411 Secondary Air Injection System Incorrect Flow Detected
P0412 Secondary Air Injection System Switching Valve A Circuit Malfunction
P0413 Secondary Air Injection System Switching Valve A Circuit Open
P0414 Secondary Air Injection System Switching Valve A Circuit Shorted
P0415 Secondary Air Injection System Switching Valve B Circuit Malfunction
P0416 Secondary Air Injection System Switching Valve B Circuit Open
P0417 Secondary Air Injection System Switching Valve B Circuit Shorted
P0418 Secondary Air Injection System Relay “A” Circuit Malfunction
P0419 Secondary Air Injection System Relay “B” Circuit Malfunction
P0420 Catalyst System Efficiency Below Threshold (Bank 1)
P0421 Warm Up Catalyst Efficiency Below Threshold (Bank 1)
P0422 Main Catalyst Efficiency Below Threshold (Bank 1)
P0423 Heated Catalyst Efficiency Below Threshold (Bank 1)
P0424 Heated Catalyst Temperature Below Threshold (Bank 1)
P0430 Catalyst System Efficiency Below Threshold (Bank 2)
P0431 Warm Up Catalyst Efficiency Below Threshold (Bank 2)
P0432 Main Catalyst Efficiency Below Threshold (Bank 2)
P0433 Heated Catalyst Efficiency Below Threshold (Bank 2)
P0434 Heated Catalyst Temperature Below Threshold (Bank 2)
P0440 Evaporative Emission Control System Malfunction
P0441 Evaporative Emission Control System Incorrect Purge Flow
P0442 Evaporative Emission Control System Leak Detected (small leak)
P0443 Evaporative Emission Control System Purge Control Valve Circuit Malfunction
P0444 Evaporative Emission Control System Purge Control Valve Circuit Open
P0445 Evaporative Emission Control System Purge Control Valve Circuit Shorted
P0446 Evaporative Emission Control System Vent Control Circuit Malfunction
P0447 Evaporative Emission Control System Vent Control Circuit Open
P0448 Evaporative Emission Control System Vent Control Circuit Shorted
P0449 Evaporative Emission Control System Vent Valve/Solenoid Circuit Malfunction
P0450 Evaporative Emission Control System Pressure Sensor Malfunction
P0451 Evaporative Emission Control System Pressure Sensor Range/Performance
P0452 Evaporative Emission Control System Pressure Sensor Low Input
P0453 Evaporative Emission Control System Pressure Sensor High Input
P0454 Evaporative Emission Control System Pressure Sensor Intermittent
P0455 Evaporative Emission Control System Leak Detected (gross leak)
P0460 Fuel Level Sensor Circuit Malfunction
P0461 Fuel Level Sensor Circuit Range/Performance
P0462 Fuel Level Sensor Circuit Low Input
P0463 Fuel Level Sensor Circuit High Input
P0464 Fuel Level Sensor Circuit Intermittent
P0465 Purge Flow Sensor Circuit Malfunction
P0466 Purge Flow Sensor Circuit Range/Performance
P0467 Purge Flow Sensor Circuit Low Input
P0468 Purge Flow Sensor Circuit High Input
P0469 Purge Flow Sensor Circuit Intermittent
P0470 Exhaust Pressure Sensor Malfunction
P0471 Exhaust Pressure Sensor Range/Performance
P0472 Exhaust Pressure Sensor Low
P0473 Exhaust Pressure Sensor High
P0474 Exhaust Pressure Sensor Intermittent
P0475 Exhaust Pressure Control Valve Malfunction
P0476 Exhaust Pressure Control Valve Range/Performance
P0477 Exhaust Pressure Control Valve Low
P0478 Exhaust Pressure Control Valve High
P0479 Exhaust Pressure Control Valve Intermittent
P0480 Cooling Fan 1 Control Circuit Malfunction
P0481 Cooling Fan 2 Control Circuit Malfunction
P0482 Cooling Fan 3 Control Circuit Malfunction
P0483 Cooling Fan Rationality Check Malfunction
P0484 Cooling Fan Circuit Over Current
P0485 Cooling Fan Power/Ground Circuit Malfunction
P0500 Vehicle Speed Sensor Malfunction
P0501 Vehicle Speed Sensor Range/Performance
P0502 Vehicle Speed Sensor Low Input
P0503 Vehicle Speed Sensor Intermittent/Erratic/High
P0505 Idle Control System Malfunction
P0506 Idle Control System RPM Lower Than Expected
P0507 Idle Control System RPM Higher Than Expected
P0510 Closed Throttle Position Switch Malfunction
P0520 Engine Oil Pressure Sensor/Switch Circuit Malfunction
P0521 Engine Oil Pressure Sensor/Switch Circuit Range/Performance
P0522 Engine Oil Pressure Sensor/Switch Circuit Low Voltage
P0523 Engine Oil Pressure Sensor/Switch Circuit High Voltage
P0530 A/C Refrigerant Pressure Sensor Circuit Malfunction
P0531 A/C Refrigerant Pressure Sensor Circuit Range/Performance
P0532 A/C Refrigerant Pressure Sensor Circuit Low Input
P0533 A/C Refrigerant Pressure Sensor Circuit High Input
P0534 Air Conditioner Refrigerant Charge Loss
P0550 Power Steering Pressure Sensor Circuit Malfunction
P0551 Power Steering Pressure Sensor Circuit Range/Performance
P0552 Power Steering Pressure Sensor Circuit Low Input
P0553 Power Steering Pressure Sensor Circuit High Input
P0554 Power Steering Pressure Sensor Circuit Intermittent
P0560 System Voltage Malfunction
P0561 System Voltage Unstable
P0562 System Voltage Low
P0563 System Voltage High
P0565 Cruise Control On Signal Malfunction
P0566 Cruise Control Off Signal Malfunction
P0567 Cruise Control Resume Signal Malfunction
P0568 Cruise Control Set Signal Malfunction
P0569 Cruise Control Coast Signal Malfunction
P0570 Cruise Control Accel Signal Malfunction
P0571 Cruise Control/Brake Switch A Circuit Malfunction
P0572 Cruise Control/Brake Switch A Circuit Low
P0573 Cruise Control/Brake Switch A Circuit High
P0574 Cruise Control Related Malfunction
P0575 Cruise Control Related Malfunction
P0576 Cruise Control Related Malfunction
P0578 Cruise Control Related Malfunction
P0579 Cruise Control Related Malfunction
P0580 Cruise Control Related Malfunction
P0600 Serial Communication Link Malfunction
P0601 Internal Control Module Memory Check Sum Error
P0602 Control Module Programming Error
P0603 Internal Control Module Keep Alive Memory (KAM) Error
P0604 Internal Control Module Random Access Memory (RAM) Error
P0605 Internal Control Module Read Only Memory (ROM) Error
P0606 PCM Processor Fault
P0608 Control Module VSS Output “A” Malfunction
P0609 Control Module VSS Output “B” Malfunction
P0620 Generator Control Circuit Malfunction
P0621 Generator Lamp “L” Control Circuit Malfunction
P0622 Generator Field “F” Control Circuit Malfunction
P0650 Malfunction Indicator Lamp (MIL) Control Circuit Malfunction
P0654 Engine RPM Output Circuit Malfunction
P0655 Engine Hot Lamp Output Control Circuit Malfucntion
P0656 Fuel Level Output Circuit Malfunction
P0700 Transmission Control System Malfunction
P0701 Transmission Control System Range/Performance
P0702 Transmission Control System Electrical
P0703 Torque Converter/Brake Switch B Circuit Malfunction
P0704 Clutch Switch Input Circuit Malfunction
P0705 Transmission Range Sensor Circuit malfunction (PRNDL Input)
P0706 Transmission Range Sensor Circuit Range/Performance
P0707 Transmission Range Sensor Circuit Low Input
P0708 Transmission Range Sensor Circuit High Input
P0709 Transmission Range Sensor Circuit Intermittent
P0710 Transmission Fluid Temperature Sensor Circuit Malfunction
P0711 Transmission Fluid Temperature Sensor Circuit Range/Performance
P0712 Transmission Fluid Temperature Sensor Circuit Low Input
P0713 Transmission Fluid Temperature Sensor Circuit High Input
P0714 Transmission Fluid Temperature Sensor Circuit Intermittent
P0715 Input/Turbine Speed Sensor Circuit Malfunction
P0716 Input/Turbine Speed Sensor Circuit Range/Performance
P0717 Input/Turbine Speed Sensor Circuit No Signal
P0718 Input/Turbine Speed Sensor Circuit Intermittent
P0719 Torque Converter/Brake Switch B Circuit Low
P0720 Output Speed Sensor Circuit Malfunction
P0721 Output Speed Sensor Range/Performance
P0722 Output Speed Sensor No Signal
P0723 Output Speed Sensor Intermittent
P0724 Torque Converter/Brake Switch B Circuit High
P0725 Engine Speed input Circuit Malfunction
P0726 Engine Speed Input Circuit Range/Performance
P0727 Engine Speed Input Circuit No Signal
P0728 Engine Speed Input Circuit Intermittent
P0730 Incorrect Gear Ratio
P0731 Gear 1 Incorrect ratio
P0732 Gear 2 Incorrect ratio
P0733 Gear 3 Incorrect ratio
P0734 Gear 4 Incorrect ratio
P0735 Gear 5 Incorrect ratio
P0736 Reverse incorrect gear ratio
P0740 Torque Converter Clutch Circuit Malfuction
P0741 Torque Converter Clutch Circuit Performance or Stuck Off
P0742 Torque Converter Clutch Circuit Stuck On
P0743 Torque Converter Clutch Circuit Electrical
P0744 Torque Converter Clutch Circuit Intermittent
P0745 Pressure Control Solenoid Malfunction
P0746 Pressure Control Solenoid Performance or Stuck Off
P0747 Pressure Control Solenoid Stuck On
P0748 Pressure Control Solenoid Electrical
P0749 Pressure Control Solenoid Intermittent
P0750 Shift Solenoid A Malfunction
P0751 Shift Solenoid A Performance or Stuck Off
P0752 Shift Solenoid A Stuck On
P0753 Shift Solenoid A Electrical
P0754 Shift Solenoid A Intermittent
P0755 Shift Solenoid B Malfunction
P0756 Shift Solenoid B Performance or Stuck Off
P0757 Shift Solenoid B Stuck On
P0758 Shift Solenoid B Electrical
P0759 Shift Solenoid B Intermittent
P0760 Shift Solenoid C Malfunction
P0761 Shift Solenoid C Performance or Stuck Off
P0762 Shift Solenoid C Stuck On
P0763 Shift Solenoid C Electrical
P0764 Shift Solenoid C Intermittent
P0765 Shift Solenoid D Malfunction
P0766 Shift Solenoid D Performance or Stuck Off
P0767 Shift Solenoid D Stuck On
P0768 Shift Solenoid D Electrical
P0769 Shift Solenoid D Intermittent
P0770 Shift Solenoid E Malfunction
P0771 Shift Solenoid E Performance or Stuck Off
P0772 Shift Solenoid E Stuck On
P0773 Shift Solenoid E Electrical
P0774 Shift Solenoid E Intermittent
P0780 Shift Malfunction
P0781 1-2 Shift Malfunction
P0782 2-3 Shift Malfunction
P0783 3-4 Shift Malfunction
P0784 4-5 Shift Malfunction
P0785 Shift/Timing Solenoid Malfunction
P0786 Shift/Timing Solenoid Range/Performance
P0787 Shift/Timing Solenoid Low
P0788 Shift/Timing Solenoid High
P0789 Shift/Timing Solenoid Intermittent
P0790 Normal/Performance Switch Circuit Malfunction
P0801 Reverse Inhibit Control Circuit Malfunction
P0803 1-4 Upshift (Skip Shift) Solenoid Control Circuit Malfunction
P0804 1-4 Upshift (Skip Shift) Lamp Control Circuit Malfunction
P0805 Clutch Position Sensor Circuit Malfunction
P0806 Clutch Position Sensor Circuit Range/Performance
P0807 Clutch Position Sensor Circuit Low
P0808 Clutch Position Sensor Circuit High
P0809 Clutch Position Sensor Circuit Intermittent Ckt
P0810 Clutch Position Control Malfunction
P0811 Clutch Slippage Excessive
P0812 Reverse Input Circuit Malfunction
P0813 Reverse Output Circuit Malfunction
P0814 Trans Range Display Circuit Malfunction
P0815 Upshift Switch Circuit Malfunction
P0816 Downshift Switch Circuit Malfunction
P0817 Starter Disable Circuit
P0818 Driveline Disconn. Switch Input
P0820 Gear Lever X-Y Sensor Circuit
P0821 Gear Lever X Sensor Circuit
P0822 Gear Lever Y Sensor Circuit
P0823 Gear Lever X Sensor Circuit Intermittent Ckt
P0824 Gear Lever Y Sensor Circuit Intermittent Ckt
P0830 Clutch Position Switch A Circuit Malfunction
P0831 Clutch Position Switch A Circuit Low
P0832 Clutch Position Switch A Circuit High
P0833 Clutch Position Switch B Circuit Malfunction
P0834 Clutch Position Switch B Circuit Low
P0835 Clutch Position Switch B Circuit High
P0836 4 Wheel Drive Switch Circuit Malfunction
P0837 4 Wheel Drive Switch CKT Range/Perf
P0838 4 Wheel Drive Switch Circuit Low
P0839 4 Wheel Drive Switch Circuit High
P0840 Trans Fluid Press Sensor/Switch A Circuit Malfunction
P0841 Trans Fluid Press Sensor/Switch A CKT Range/Perf
P0842 Trans Fluid Press Sensor/Switch A Circuit Low
P0843 Trans Fluid Press Sensor/Switch A Circuit High
P0844 Trans Fluid Press Sensor/Switch A CKT Intermittent
P0845 Trans Fluid Press Sensor/Switch B Circuit Malfunction
P0846 Trans Fluid Press Sensor/Switch B CKT Range/Perf
P0847 Trans Fluid Press Sensor/Switch B Circuit Low
P0848 Trans Fluid Press Sensor/Switch B Circuit High
P0849 Trans Fluid Press Sensor/Switch B CKT Intermittent
P1000 Electronic Gear Selector Module: Defective N15/5
P1031 component G3/3 (O2-in CAT front left detector) and G3/4 (O2-in CAT front right detector) exchange
P1032 O2 sensors upstream TWC mixed up G3/3,G3/4
P1105 Altitude pressure sensor control module
P1105 Atmospheric pressure sensor Readout too large.
P1105 Atmospheric pressure sensor Readout too small.
P1105 high pressure sensor controller
P1146 left HF type AFM sensor (B2/6)
P1147 left coolant temperature sensor (B11/9)
P1148 left intake air temperature sensor (B17/5)
P1149 left pressure sensor (B28/1)
P1162 left regulation part practical potentiometer
P1163 engine oil condition control switch (S43)
P1163 Oil sensor:engine oil level implausible (B10)
P1176 engine oil sensor (B40)
P1176 Oil pressure sensor malfunction (B10)
P1177 engine oil sensor (B40) engine oil temperature error
P1177 Oil sensor:engine oil temperature implausible (B10)
P1178 engine oil sensor (B40) engine oil condition error
P1178 Oil sensor:engine oil level implausible (B10)
P1179 engine oil sensor (B40) engine oil quality error
P1179 Oil sensor:engine oil quality implausible (B10)
P1180 engine oil sensor (B40) engine oil temperature too high
P1180 Oil sensor:engine oil temperature too high (B10)
P1181 Electric induction fan Engine/AC malfunction (M34)
P1181 engine/A/C electronic suction device (M4/3) rating RPM error
P1183 Malfunction right cylinder shut-off output stage
P1184 Malfunction left cylinder shut-off output stage
P1185 engine oil sensor (B40) water in engine oil
P1185 Oil sensor:water in engine oil (B10)
P1186 Safety fuel shut-off
P1187 fuel rail pressure inspection
P1187 Rail pressure monitoring Control variation < 1500/min (rpm) P1187 Rail pressure monitoring Control variation > 1500/min (rpm)
P1187 Rail pressure monitoring Leakage
P1187 Rail pressure monitoring The maximum pressure has been exceeded.
P1187 Rail pressure monitoring The pressure control valve jams in the closed position.
P1187 Rail pressure monitoring The rail pressure cannot be built up.
P1187 Rail pressure monitoring The rail pressure is too low.
P1189 Inlet port shutoff M55 (Inlet port shutoff motor)
P1189 Inlet port shutoff Open circuit
P1189 Inlet port shutoff Short circuit
P1189 Inlet port shutoff The flaps jam in the closed position.
P1189 Inlet port shutoff The flaps jam in the open position.
P1189 intake air turnoff switch valve Y83
P1190 Fuel pressure control valve N3/9 (CDI control module)
P1190 Fuel pressure control valve Open circuit
P1190 Fuel pressure control valve Short circuit
P1190 fuel pressure regulation valve Y74
P1192 B40 (Oil sensor (oil level,temperature and quality)) Oil level is implausible.
P1192 B40 (Oil sensor (oil level,temperature and quality)) Oil quality is implausible.
P1192 B40 (Oil sensor (oil level,temperature and quality)) Oil temperature is implausible.
P1192 B40 (Oil sensor (oil level,temperature and quality)) Period error of oil sensor
P1192 B40 (Oil sensor (oil level,temperature and quality)) Short circuit/Open circuit
P1192 B40 (Oil sensor (oil level,temperature and quality)) Synchronization pause is breached.
P1192 B40 (Oil sensor (oil level,temperature and quality)) The supply voltage is too high or too low.
P1192 B40 (Oil sensor (oil level,temperature and quality)) Water in engine oil P1192 engine oil sensor B40
P1220 Fuel metering control Y23/1
P1221 CAN communication if faulty.Fault of ETC over CAN
P1221 CAN communication is faulty.Fault of traction system over CAN
P1221 CAN reception from ASR/ETC/ESP
P1221 CAN signal from ASR/EGS/ESP
P1222 accelerator pedal position sensor B37
P1222 B37 (Pedal value sensor) Sensor 1 Plausibility 1
P1222 B37 (Pedal value sensor) Sensor 1 Plausibility 2
P1222 B37 (Pedal value sensor) Sensor 1 Plausibility 3
P1222 B37 (Pedal value sensor) Sensor 1 The signal voltage is too high.
P1222 B37 (Pedal value sensor) Sensor 1 The signal voltage is too low.
P1222 B37 (Pedal value sensor) Sensor 1 The supply voltage is too high or too low.
P1222 Potentiometer R25/2
P1223 Distributer shaft position sensor Y23/2|2
P1223 Fuel rack travel sensor or slide valve position sensor Y23/11
P1224 Fuel metering control
P1225 Intake pressure control
P1225 Resonance intake manifold switchover valve (Y77)
P1226 Cam ring position sensor Y23/2|1
P1227 Distributer shaft position sensor Y23/2|2
P1228 Injection pump quantity stop
P1228 yet unknown code on 1997 C 220 CDI
P1229 Balancing resistor Y23/2r2
P1230 Cam ring position sensor Y23/2|1
P1233 Throttle valve actuator jamming (iced up) M16/6
P1234 accelerator pedal position sensor B37
P1234 B37 (Pedal value sensor) Sensor 2 IMPLAUSIBLE Sensor 1/2
P1234 B37 (Pedal value sensor) Sensor 2 The signal voltage is too high.
P1234 B37 (Pedal value sensor) Sensor 2 The signal voltage is too low.
P1234 B37 (Pedal value sensor) Sensor 2 The supply voltage is too high or too low.
P1235 Recirculated air flap signal output stage
P1236 Compressor output stage magnetic coupling
P1237 read traction control system fault memory
P1300 left crankshaft position sensor (L5/4)
P1330 start control
P1330 Starter control
P1330 Starter control Attempt at starting without circuit 50
P1330 Starter control Open circuit
P1330 Starter control Short circuit
P1335 Crankshaft position sensor L5/6
P1335 L5 (Crankshaft position sensor) Overspeed detection
P1335 L5 (Crankshaft position sensor) Plausibility 1
P1335 L5 (Crankshaft position sensor) Plausibility 2
P1350 Injection advance solenoid valve
P1351 Start of delivery /injection control loop
P1352 Needle lift motion sensor B27
P1353 Working speed control
P1354 deflexion angle between camshaft and crankshaft
P1354 Synchronization between crankshaft and camshaft Frequency of camshaft signal is too high.
P1354 Synchronization between crankshaft and camshaft Main injection correction is faulty.
P1354 Synchronization between crankshaft and camshaft No camshaft signal.
P1354 Synchronization between crankshaft and camshaft No crankshaft signal.
P1354 Synchronization between crankshaft and camshaft Plausibility
P1354 Synchronization between crankshaft and camshaft The flow limiter has been activated.
P1355 component Y80 (valve OFF,right cylinder) can not be off while cylinder is cut-off (OFF)
P1356 component Y81 (valve OFF,left cylinder) can not be off while cylinder is cut-off (OFF)
P1357 cylinder cut-off (function link):cylinder intake valve still works when cylinder is cut-off (ON)
P1358 cylinder 5 exhaust valve can not work when cylinder is cut-off (OFF)(function link)
P1359 cylinder 2 exhaust valve can not work when cylinder is cut-off (OFF)(function link)
P1360 cylinder 3 exhaust valve can not work when cylinder is cut-off (OFF)(function link)
P1361 cylinder 8 exhaust valve can not work when cylinder is cut-off (OFF)(function link)
P1366 Y93 (switch-over valve exhaust valve)
P1380 cylinder intake valve can not work when cylinder is cut-off (OFF)
P1384 FL knock sensor
P1385 RL knock sensor
P1386 knock control
P1386 Knock sensor system control module control stop (A61)
P1386 right remove knock regulation controller (N3/12)
P1397 left camshaft Hall sensor (B6/2)
P1400 Exhaust gas recirculation output stage (Y12)
P1401 EGR lift sensor B28/3
P1402 Exhaust gas recirculation open-loop control
P1403 Exhaust gas recirculation Flow check
P1403 exhaust gas recirculation HFM-regulation
P1403 Exhaust gas recirculation HFM-SFI-controlled
P1403 Exhaust gas recirculation Open circuit
P1403 Exhaust gas recirculation Positive control variation [Exhaust gas recirculation rate is too high.]
P1403 Exhaust gas recirculation Positive control variation [Exhaust gas recirculation rate is too low.]
P1403 Exhaust gas recirculation Short circuit
P1404 Exhaust gas recirculation AHR closed-loop control
P1411 EGR lift sensor
P1420 Air pump switchover valve (Y32)
P1420 air pump switch-over valve (Y32)
P1437 No fault text specified at present.
P1437 right CAT temperature sensor (B16/5)
P1443 left work link EGR
P1444 left CAT temperature sensor (B16/4)
P1444 No fault text specified at present.
P1453 air pump relay (K17)
P1453 Air pump relay (K17),relay module K76,fuse and relay module K40/4
P1460 Switchover valve 1 Y22 /7
P1461 Switchover valve 2 Y22 /6
P1463 left air inbreathe device inactive
P1465 Boost pressure control vacuum transducer
P1470 Charge pressure control On/off ration of actuation is too large.
P1470 Charge pressure control Open circuit
P1470 Charge pressure control Positive control variation [Charge pressure is too high.]
P1470 Charge pressure control Positive control variation [Charge pressure is too low.]
P1470 Charge pressure control Short circuit
P1470 intake air pressure regulation
P1470 Intake pressure or boost pressure control
P1475 Resonance intake manifold switchover valve Y22/6
P1476 Resonance flap intake pipe Y22/7
P1480 Preglow indicator
P1480 pre-heating control
P1481 Glow plug failure
P1481 Glow plug failure Cylinder 1
P1481 Glow plug failure Cylinder 2
P1481 Glow plug failure Cylinder 3
P1481 Glow plug failure Cylinder 4
P1481 Glow plug failure Cylinder 5
P1481 Glow plug failure Cylinder 6
P1481 Glow plug failure Cylinder 7
P1481 Glow plug failure Cylinder 8
P1481 Glow Plugs
P1481 pre-heating plug fault
P1482 Glow output stage N14/2
P1482 N14/2 (Glow output stage) Cable fault (Short circuit to ground)
P1482 N14/2 (Glow output stage) Communication fault
P1482 N14/2 (Glow output stage) Excess current
P1482 N14/2 (Glow output stage) FAULTY
P1482 N14/2 (Glow output stage) Implausible reception byte
P1482 N14/2 (Glow output stage) Incorrect diagnosis sequence
P1482 pre-heating plug output stage N14/2
P1490 left EGR device switch-over valve (Y58/2)
P1491 Refrigerant pressure in A/C system too high
P1492 Exhaust flap (not relevant if not fitted)
P1493 Exhaust flap output stage (not relevant if not fitted)
P1510-001 speed meter touch switch (S40/4)
P1510-003 MSM1 controller N3/5
P1515 maximal speed limit negative difference
P1515 maximal vehicle speed limit
P1515 Maximum speed limiter
P1519 Camshaft timing function chain
P1519 right work link camshaft control device
P1520 Cruise control switch S40
P1520 S40/4 (CC switch with variable speed limiter) Control contact alone
P1520 S40/4 (CC switch with variable speed limiter) DTR operating unit has contact short (two contacts simultaneously).
P1520 S40/4 (CC switch with variable speed limiter) Negative acceleration threshold
P1520 S40/4 (CC switch with variable speed limiter) No check contact.
P1520 S40/4 (CC switch with variable speed limiter) Operating parts signals through CAN are implausible.
P1520 S40/4 (CC switch with variable speed limiter) Positive acceleration threshold
P1520 speed controller button type switch
P1522 left work link camshaft control device
P1525 Camshaft timing actuator (Y89)
P1525 right camshaft control device regulation solenoid valve (Y49/2)
P1533 right camshaft control device regulation solenoid valve (Y49/1)
P1542 Pedal value sensor (B71)
P1550 air compressor torque error
P1551 AC compressor shut-off output stage
P1570 Fault in DAS to engine control module (A61)
P1570 Intermittant No-Start Immobiliser Module
P1570 perform start test while closedown FBS
P1570 right FBS and engine controller interfered (N3/12)
P1580 Actuator (M33)
P1580 right regulation part (M16/3)
P1581 left regulation part (M16/4)
P1584 brake light switch (S9/1)
P1587 left controller voltage (N3/11)
P1588 left FBS to ME CAN BUS interfered (N3/11)
P1589 right removing knock regulation controller (N3/11)
P1590 fuel safety cut-off device identified
P1592 ACS memory read error
P1603 CAN of EIS
P1604 CAN link to AAC
P1605 ABS RPM sensor bad channel identification CAN BUS acceleration signal
P1605 CAN acceleration info for poor road recognition from ABS speed sensor
P1610 Actuation of holding relay Relay Supply voltages switches off too late.
P1610 Actuation of holding relay Relay Supply voltages switches off too soon.
P1610 No voltage supply or overvoltage protection relay or relay module K1
P1610 security and relay module K40/4
P1611 Control module
P1611 controller N3/9
P1611 N3/9 (CDI control module) Sensor supply voltage 1 Readout too large
P1611 N3/9 (CDI control module) Sensor supply voltage 1 Readout too small
P1612 Control module Kl 15
P1612 signal Kl15
P1612 Voltage terminal 15
P1612 Voltage terminal 15 Analysis circuit is faulty.
P1613 Control module
P1613 controller N3/9
P1613 N3/9 (CDI control module) Stabilization Lower stabilization limit
P1613 N3/9 (CDI control module) Stabilization Upper stabilization limit
P1614 Control module or fuel metering control or fuel rack sensor or slide valve sensor
P1614 controller N3/9
P1614 N3/9 (CDI control module) Microcontroller COMMUNICATION 1
P1614 N3/9 (CDI control module) Microcontroller COMMUNICATION 2
P1614 N3/9 (CDI control module) Microcontroller Quantity stop
P1614 N3/9 (CDI control module) Microcontroller Recovery error
P1614 N3/9 (CDI control module) Microcontroller Shut-off monitoring
P1615 Control module supply voltage
P1615 controller supply voltage
P1615 N3/9 (CDI control module) Supply voltage Signal is too large.
P1615 N3/9 (CDI control module) Supply voltage Signal is too small.
P1616 Control module
P1617 Control module or not coded
P1617 controller N3/9 or not coded
P1617 EEPROM or incorrectly coded Adaptation values of EEPROM
P1617 EEPROM or incorrectly coded AT has been coded as MT.
P1617 EEPROM or incorrectly coded CAN was interrupted during coding.
P1617 EEPROM or incorrectly coded Codeword is incorrect or missing.
P1617 EEPROM or incorrectly coded EEPROM COMMUNICATION
P1617 EEPROM or incorrectly coded MT has been coded as AT.
P1617 EEPROM or incorrectly coded No harmonizing version number
P1618 Control module
P1619 Control module or not coded
P1622 Injection pump shut-off valve
P1622 turnoff valve Y75
P1622 Y75 (Electric switchover valve) Open circuit
P1622 Y75 (Electric switchover valve) Plausibility
P1622 Y75 (Electric switchover valve) Short circuit
P1622 Y75 Electric switchover valve open circuit
P1625 EDC diesel malfunction indicator lamp
P1626 Engine mount
P1630 drive authority signal
P1630 Drive authorization Control unit Drive authorization does not answer
P1630 Drive authorization Incorrect authentication value
P1630 Drive authorization Key used is inhibited.
P1630 Drive authorization N3/9 (CDI control module) EEPROM
P1630 Drive authorization signal
P1631 Slip detection signal
P1632 left controller (N3/11)
P1636 electric inspiration motor/air condition M4/3
P1636 Electric suction fan Open circuit
P1636 Electric suction fan Short circuit
P1642 Engine control module Incorrect coding MT coded has AT
P1643 Engine control module Incorrect coding AT coded has MT,fault in CAN of ETC
P1644 Transmission control module Undervoltage Transmission version cannot be checked
P1644 transmission variable cannot be inspected (low voltage)
P1650-001 starter short circuit to positive
P1650-002 starter discontinuity,short circuit to ground
P1661 fuel injector 1 and 4 fuel injector pressure
P1661 Injector voltage 1 Calculated voltage below threshold
P1661 Injector voltage 1 Overvoltage
P1661 Injector voltage 1 Readout too large
P1661 Injector voltage 1 Readout too small
P1661 Injector voltage 1 Undervoltage
P1662 fuel injector 2 and 3 fuel injector pressure
P1662 Injector voltage 2 Calculated voltage below threshold
P1662 Injector voltage 2 Overvoltage
P1662 Injector voltage 2 Readout too large
P1662 Injector voltage 2 Readout too small
P1662 Injector voltage 2 Undervoltage
P1663 fuel pressure regulator Y74
P1663 Y74 (Pressure control valve) The signal voltage is too high.
P1663 Y74 (Pressure control valve) The signal voltage is too low.
P1664 Electric heater booster equipment fault
P1664 electric heater fault
P1664 electric heater open
P1664 electric heater output stage fault
P1664 electric heater short
P1664 heater
P1664 load signal of electric heater motor implausible
P1666 cutoff control
P1666 right or left cylinder (Y80,Y81) ‘cylinder cut-off’ valve can not be turned on when cylinder is cut-off.
P1666 Shut-off control Fault in switching off throutgh injectors
P1666 Shut-off control Fault in switching off throutgh zero quantity
P1673-001 engine/A/C electronic suction device (M4/3) short circuit to positive
P1673-002 engine/A/C electronic suction device (M4/3) short circuit to ground
P1681 air bag signal
P1681 Airbag signal Airbag signal results in engine being switched off.
P1681 Airbag signal Short circuit to positive
P1681 Crash-Signal unplausibel
P1681-001 crash signal identification
P1681-002 crash signal short circuit to positive
P1681-003 crash signal error
P1698 A/C compressor cutoff
P1698 AC compressor shutoff CAN data transfer
P1698 AC compressor shutoff Open circuit
P1698 AC compressor shutoff Short circuit
P1699 Engine start/stop Engine start is unsuccessful.
P1699 Engine start/stop Engine stop is unsuccessful.
P1699 Engine start/stop Plausibility 1
P1699 Engine start/stop Plausibility 2
P1699 Engine start/stop Plausibility 3
P1699 Engine start/stop Plausibility clutch DOWN
P1699 Engine start/stop Plausibility clutch UP
P1705 Clutch signal or P/N position
P1705 Clutch signal or P/N position Plausibility
P1705 clutch switch
P1705 Clutch switch or starter lockout and reversing lamp switch
P1706 Transmisson neutral switch
P1747 control equipment EGS CAN-signal error.
P1747 control equipment KIW CAN-signal error.
P1747 EGS CAN BUS interfered
P1747 Electronic Gear Selector Module: Defective Interaction of CAN with control unit A1(instrument cluster)
P1750 Electronic Gear Selector Module: Very low control unit supply voltage
P1750 undervoltage
P1780 Modulating pressure switchover valve Y3/4
P1780 Modulating pressure switchover valve Y3/4 or upshift delay Y3/5
P1781 Upshift delay switchover valve Y3/5
P1813 clutch switch (S40/3) discontinuity,short circuit to ground
P1817-001 reversing light switch S16/10s1 contact point short circuit to ground
P1817-002 reversing light switch S16/10s1 contact point short circuit to positive
P1817-003 reversing light switch S16/10s1 contact point discontinuity
P1817-004 reversing light switch S16/10s1 A61 fault
P1817-005 reversing light switch S16/10s1 power voltage
P1819-001 R/P lock contact switch short circuit to ground
P1819-002 R/P lock contact switch short circuit to positive
P1819-003 R/P lock contact switch discontinuity
P1819-004 R/P lock contact switch,A61 fault
P1819-005 R/P lock contact switch supply voltage
P1822 kickdown switch (S16/6) error
P1832 Electronic Gear Selector Module: SHORT in circuit N15/5 output stage
P1840 1-4 shift solenoid valve Y3/7y1
P1841 Solenoid valve Y3/7y2 3 shift
P1842 Solenoid valve Y3/7y3 2-5-R shift
P1843 Torque converter lockup clutch (KUeB) Y3/7y4
P1844 Control solenoid valve Y3/7y5 shift pressure
P1849 Speed sensors supply voltage < 4 V
P1850 Transmission rpm sensor Y3/7n1
P1856-000 process recognition module
P1856-001 touch-function module
P1857 Gear oil temperature sensor Y3/7b1
P1858 Starter lockout contact Y3/7s1 short circuit
P1859 Supply voltage < 8.5 V or > 17 V
P1860 RR wheel speed of traction system implausible,CAN
P1861 RL wheel speed of traction system implausible,CAN
P1862 FR wheel speed of traction system implausible,CAN
P1863 FL wheel speed of traction system implausible,CAN
P1864 Accel.pedal value of motor electronics implausible,CAN
P1865 Set engine torque of motor electronics implausible,CAN
P1866 Engine speed of motor electronics implausible,CAN
P1867 Engine torque of motor electronics implausible,CAN
P1868 Altitude factor of motor electronics implausible,CAN
P1869 Max.induced engine torque of motor electronics implausible,CAN
P1871 Throttle valve value of motor electronics implausible,CAN
P1872 Fault in CAN communication with selector lever module or selector lever implausible
P1873 Fault in CAN communication with traction system
P1874 Engine oil temperature of motor electronics implausible,CAN
P1875-000 common CAN communication interfered
P1875-001 CAN communication with instrument cluster interfered
P1875-001…255 same meaning
P1875-255 CAN communication with instrument cluster interfered
P1876 Fault in CAN communication with traction system
P1877 Fault in CAN communication with engine electronics
P1878 Fault in CAN communication with air conditioning
P1883 Transmission complete
P1886 1-4/-3 downshift PWM valve,pressure too low or 2-5-R pressure too high
P1887 1-4 or 2-5 shift slide valve jamming in pressure position,shift valve pressure too high
P1888 1-4 or 2-5 shift slide valve jamming in basic position,shift valve pressure too low
P1889 2-5-R downshift PWM valve pressure too low transmission slipping
P1890 Torque converter lockup clutch,impermissible closing
P1891 Torque converter lockup clutch,high power input
P1892 Transmission protection feedback not received
P1893 1-4/-3 downshift PWM valve,pressure too high
P1894 Control module not/incorrectly coded
P1895 Control module N15/7 faulty
P1896 Control module N15/7 faulty
P1897 Control module N15/7 faulty
P1898 Control module N15/7 faulty
P1899 Control module N15/7 faulty
P1900 Control module N15/7 faulty
P1901 Control module N15/7 faulty
P1902 Control module N15/7 faulty
P1903 Control module N15/7 faulty
P1910 Electronic Gear Selector Module: Control Unit over voltage
P1912 Electronic Gear Selector Module: Weak touch push button voltage
P1999 No fault text specified at present.
P2000 Component N15/3 (ETC control module) is faulty.
P2000 Component N15/3(ETC control module) is faulty.
P2000 N3/9 (controller CDI) [checksum:error]
P2000 N3/9 (controller CDI) component N3/9 (controller CDI) error variable code
P2000 N3/9 (controller CDI) engine synthesis characteristic curve error:error code
P2000 N3/9 (controller CDI) hardware identification error.
P2000 N3/9 (controller CDI) internal error
P2000 N3/9 (controller CDI) software ‘integration check’ error.
P2000 N3/9 (controller CDI) thruster controller test
P2000 N3/9 (controller CDI) variable code error.
P2000 NOx Trap Efficiency Below Threshold (Bank 1)
P2001 – [8] M16/6 (throttle valve actuator) ,: M16/6 (throttle valve actuator) , PWM signal: threshold 1
P2001 P0638 [1] M16/6 (throttle valve actuator) ,: Plausibility Position Throttle valve [P0638]
P2001 P0638 [2] M16/6 (throttle valve actuator) ,: M16/6 (throttle valve actuator) , PWM signal: threshold 2 [P0638]
P2001 P0638 [4] M16/6 (throttle valve actuator) ,: M16/6 (throttle valve actuator) , PWM signal switched off [P0638]
P2001 check N3/9 (controller CDI) A/D converter.
P2001 check N3/9 (controller CDI) reference voltage
P2001 check N3/9 (controller CDI) voltage supply 1.
P2001 check N3/9 (controller CDI) voltage supply 2.
P2001 check N3/9 (controller CDI).Circuit voltage supply unit fault
P2001 Component N15/3 (ETC control module) is faulty.
P2001 Malfunction of exhaust gas recirculation (functional chain)(P0400)
P2001 N3/9 (controller CDI) reset identification error
P2001 NOx Trap Efficiency Below Threshold (Bank 2)
P2001-001 M16/6 (throttle valve regulation part),throttle valve position reliability [P0638]
P2001-002 M16/6 (throttle valve regulation part),PWM-signal:limit 2[P0638]
P2001-004 M16/6 (throttle valve regulation part),PWM-signal interrupt [P0638]
P2001-008 M16/6 (throttle valve regulation part),PWM-signal:limit 1
P2002 P0121 [16] B37 (Pedal value sensor): , Voltage of Hall sensor 1 does not agree with voltage of Hall sensor 2. [P0121]
P2002 P0122 [2] B37 (Pedal value sensor): Hall sensor 1 , Short circuit to ground / Open circuit in wiring [P0122]
P2002 P0123 [1] B37 (Pedal value sensor): Hall sensor 1 , Short circuit to positive [P0123]
P2002 P0222 [8] B37 (Pedal value sensor): Hall sensor 2 , Short circuit to ground / Open circuit in wiring [P0222]
P2002 P0223 [4] B37 (Pedal value sensor): Hall sensor 2 , Short circuit to positive [P0223]
P2002 Component N15/3(ETC control module) is faulty.
P2002 cylinder 1 lasting injection
P2002 cylinder 2 lasting injection
P2002 cylinder 3 lasting injection
P2002 cylinder 4 lasting injection
P2002 cylinder 5 lasting injection
P2002 cylinder 6 lasting injection
P2002 cylinder 7 lasting injection
P2002 cylinder 8 lasting injection
P2002-001 B37 (pedal position sensor) Hall sensor 1,positive short [P0123]
P2002-002 B37 (pedal position sensor) Hall sensor 1,short caused by open wire [P0122]
P2002-004 B37 (pedal position sensor) Hall sensor 2,positive short [P0223]
P2002-008 B37 (pedal position sensor) Hall sensor 2,short caused by open wire [P0222]
P2002-016 B37 (pedal position sensor) Hall sensor 1 voltage and Hall sensor 2 voltage not match [P0121]
P2003 – [1] The supply voltage of the sensors at the control module is not within the permissible range. ,: Overvoltage
P2003 – [2] The supply voltage of the sensors at the control module is not within the permissible range. ,: Undervoltage
P2003 check position regulator.Left air mass boost balance position on the high side
P2003 check position regulator.Right air mass boost balance position on the high side
P2003 Component N15/3(ETC control module) is faulty.
P2003 Malfunction of secondary air injection (function chain)(P0410)
P2003 Particulate Trap Efficiency Below Threshold (Bank 1)
P2003 right cylinder bank intake error (work link)(P0410)
P2003-001 controller sensor voltage supply over range,voltage too high
P2003-002 controller sensor voltage over range,voltage too high
P2004 P0106 [4] B18 (Altitude pressure sensor) Signal ,: Signal B28 (Pressure sensor) not equal to signal B18 (Altitude pressure sensor) when engine not running [P0106]
P2004 P0107 [2] B18 (Altitude pressure sensor) Signal ,: Short circuit to ground [P0107]
P2004 P0108 [1] B18 (Altitude pressure sensor) Signal ,: Short circuit to positive / Open circuit in wiring [P0108]
P2004 B2/5 (HFM sensor)(P0100)
P2004 B2/5 (Hot film MAF sensor)(P0100)
P2004 check external voltage supply.Battery voltage too high
P2004 check external voltage supply.Battery voltage too low
P2004 check external voltage supply.Control of holding relay K40/7km (relay CDI) cutoff too early.
P2004 check external voltage supply.KI.15:hardware (HW) turn-on;CAN-BUS turnoff
P2004 check external voltage supply.Relay (diesel engine voltage supply relay) cutoff too late.
P2004 Component N15/3(ETC control module) is faulty.
P2004 Particulate Trap Efficiency Below Threshold (Bank 2)
P2004-001 B18 (high pressure sensor) signal,positive/wire open cause short [P0108]
P2004-002 B18 (high pressure sensor) signal,overload short [P0107]
P2004-004 B18 (high pressure sensor) signal,engine off B28 (pressure sensor) signal and B18 (high pressure sensor) signal different[P0106]
P2005 – [32] B11/4 (Coolant temperature sensor) ,: Coolant temperature rises too slowly.
P2005 P0116 [8] B11/4 (Coolant temperature sensor) ,: Signal IMPLAUSIBLE [P0116]
P2005 P0117 [2] B11/4 (Coolant temperature sensor) ,: Short circuit to ground [P0117]
P2005 P0118 [1] B11/4 (Coolant temperature sensor) ,: Short circuit to positive / Open circuit in wiring [P0118]
P2005 P0119 [16] B11/4 (Coolant temperature sensor) ,: Signal IMPLAUSIBLE [P0119]
P2005 P0125 [4] B11/4 (Coolant temperature sensor) ,: Minimum engine temperature for lambda control has not been reached. [P0125]
P2005 B11/4 (Coolant temperature sensor)(P0115)
P2005 B11/4 (refrigerant temperature sensor)(P0115)
P2005 check L5 (crankshaft position sensor).Impulse number invalid
P2005 check L5 (crankshaft position sensor).Negative rotate speed grads too large
P2005 check L5 (crankshaft position sensor).Over speed
P2005 check L5 (crankshaft position sensor).Positive rotate speed grads too large
P2005 check L5 (crankshaft position sensor).Signal interrupted while operating
P2005 check L5 (crankshaft position sensor).Signal interrupted while starting
P2005 check L5 (crankshaft position sensor).Synchronization between crankshaft and camshaft implausible
P2005 Component N15/3(ETC control module) is faulty.
P2005-001 B11/4 (refrigerant temperature sensor),positive/wire open cause short [P0118]
P2005-002 B11/4 (refrigerant temperature sensor),overload short [P0117]
P2005-004 B11/4 (refrigerant temperature sensor),¦Ë adaptation required minimal engine rpm not reach [P0125]
P2005-004 B11/4 (refrigerant temperature sensor),¦Ë adaptation required minimal engine rpm not reach [P0125]
P2005-008 B11/4 (refrigerant temperature sensor),signal error [P0116]
P2005-016 B11/4 (refrigerant temperature sensor),signal error [P0119]
P2005-032 refrigerant temperature rise too slow.[P0128]
P2006 P0112 [2] B2/5b1 (Intake air temperature sensor) Signal ,: Short circuit to ground [P0112]
P2006 P0113 [1] B2/5b1 (Intake air temperature sensor) Signal ,: Short circuit to positive / Open circuit in wiring [P0113]
P2006 B2/5b1 (intake temperature sensor) (P0110)
P2006 check B6/1 (camshaft Hall sensor). Signal too strong. Short to positive
P2006 check B6/1 (camshaft Hall sensor). Signal too weak. Short to ground
P2006 Component N15/3(ETC control module) is faulty.
P2006 fuel pre-supply pressure sensor implausible
P2006 fuel pre-supply pressure sensor signal value too large
P2006 fuel pre-supply pressure sensor signal value too small
P2006-001 B2/5b1 (outside air temperature sensor) signal, positive/wire open cause short [p0113]
P2006-002 B2/5b1 (outside air temperature sensor) signal, overload short [P0112]
P2007 B28 (Pressure sensor)(P0105)
P2007 check B11/4 (coolant temperature sensor).Dynamic check implausible.
P2007 check B11/4 (coolant temperature sensor).Signal voltage too high.
P2007 check B11/4 (coolant temperature sensor).Signal voltage too low.
P2007 Component N15/3(ETC control module) is faulty.
P2007 control fuel pre-supply pressure, reliability
P2007 inspect difference between fuel pre-supply pressure and rating pressure
P2007 inspect fuel pre-supply pressure, fuel filter break
P2007 inspect fuel pre-supply pressure, fuel pre-supply pressure too low
P2007-001 A16 (knock sensor) [P0325]
P2008 – [1] M16/6 (throttle valve actuator) Actual value potentiometer 1,: The signal voltage is too high.
P2008 – [2] M16/6 (throttle valve actuator) Actual value potentiometer 1,: The signal voltage is too low.
P2008 – [4] M16/6 (throttle valve actuator) Actual value potentiometer 1,: Comparative error to actual value potentiometer 2
P2008 – [8] M16/6 (throttle valve actuator) Actual value potentiometer 1,: Comparative error to signal HFM-SFI voltage
P2008 check B40 (engine oil sensor (level,temperature and quality)). Engine oil sensor intermittent error
P2008 check B40 (engine oil sensor (level,temperature and quality)). Level implausible.
P2008 check B40 (engine oil sensor (level,temperature and quality)). Not break down synchronously.
P2008 check B40 (engine oil sensor (level,temperature and quality)). Oil quality implausible.
P2008 check B40 (engine oil sensor (level,temperature and quality)). Oil temperature implausible.
P2008 check B40 (engine oil sensor (level,temperature and quality)). Short/no signal.
P2008 component G3/9 (right O2 sensor,before CAT,CYL 1-3) heating (P0135)
P2008 Component N15/3(ETC control module) is faulty.
P2008 Heating of component G3/4 (Right O2 sensor,before TWC[CAT])(P0135)
P2008 Rail pressure variation:The rail pressure is too high.
P2008 Rail pressure variation:The rail pressure is too low.
P2008-001 M16/6 (throttle valve regulation part) practical potentiometer 1,signal voltage too high.
P2008-002 M16/6 (throttle valve regulation part) practical potentiometer 1,signal voltage too low.
P2008-004 M16/6 (throttle valve regulation part) practical potentiometer 1 and practical potentiometer 2 comparison error
P2008-008 M16/6 (throttle valve regulation part) practical potentiometer 1 and HFM voltage signal comparison error
P2009 – [1] M16/6 (throttle valve actuator) Actual value potentiometer 2,: The signal voltage is too high.
P2009 – [2] M16/6 (throttle valve actuator) Actual value potentiometer 2,: The signal voltage is too low.
P2009 – [4] M16/6 (throttle valve actuator) Actual value potentiometer 2,: Comparative error to actual value potentiometer 1
P2009 – [8] M16/6 (throttle valve actuator) Actual value potentiometer 2,: Comparative error to signal HFM-SFI voltage
P2009 check B4/6 (fuel rail pressure sensor).Signal voltage too high.
P2009 check B4/6 (fuel rail pressure sensor).Signal voltage too low.
P2009 component G3/13 (right O2 sensor,after CAT,CYL 1-3)(P0141)
P2009 Component N15/3(ETC control module) is faulty.
P2009 fuel water content sensor.(fuel filter)
P2009 Heating of component G3/6 (Right O2 sensor,after TWC[CAT])(P0141)
P2009-001 M16/6 (throttle valve regulation part) practical potentiometer 2,signal voltage too high.
P2009-002 M16/6 (throttle valve regulation part) practical potentiometer 2,signal voltage too low.
P2009-004 M16/6 (throttle valve regulation part) practical potentiometer 2,practical potentiometer 1 comparison error
P2009-008 M16/6 (throttle valve regulation part) practical potentiometer 2 and HFM voltage signal comparison error
P200A – [1] M16/6 (throttle valve actuator) Actual value potentiometer ,: First initialization
P200A – [2] M16/6 (throttle valve actuator) Actual value potentiometer ,: Position Emergency running
P200A – [4] M16/6 (throttle valve actuator) Actual value potentiometer ,: Adaptation Emergency running
P200A – [8] M16/6 (throttle valve actuator) Actual value potentiometer ,: N3/10 (ME-SFI control module)
P200A Component N15/3(ETC control module) is faulty.
P200A Knock sensor system of control module N3/10 (ME-SFI control module),Hardware fault
P200A-001 M16/6 (throttle valve regulation part) practical potentiometer,not initialization
P200A-002 M16/6 (throttle valve regulation part) practical potentiometer,position urgency start
P200A-004 M16/6 (throttle valve regulation part) practical potentiometer,adaptation urgency start
P200A-008 M16/6 (throttle valve regulation part) practical potentiometer,N3/10 (ME controller)
P200B P0101 [4] B2/5 (Hot film MAF sensor) ,: Plausibility error Air mass meter / Throttle valve [P0101]
P200B P0102 [2] B2/5 (Hot film MAF sensor) ,: Short circuit to ground / Open circuit in wiring [P0102]
P200B P0103 [1] B2/5 (Hot film MAF sensor) ,: Short circuit to positive [P0103]
P200B Component N15/3(ETC control module) is faulty.
P200B cylinder 1-3 CAT too weak.(P0422)
P200B The efficiency of the right catalytic converter is insufficient.(P0422)
P200B-001 B2/5 (HF type AFM sensor),positive short [P0103]
P200B-002 B2/5 (HF type AFM sensor),overload/wire open cause short [P0102]
P200B-004 B2/5 (HF type AFM sensor),air mass sensor/throttle valve reliability error [P0101]
P200C P0340 [1] B6/1 (Camshaft Hall sensor) ,: No signal [P0340]
P200C P0341 [2] B6/1 (Camshaft Hall sensor) ,: Signal IMPLAUSIBLE [P0341]
P200C Component N15/3(ETC control module) is faulty.
P200C G3/4 (Right O2 sensor,before TWC[CAT]) Aging,correction variable exceeded
P200C G3/9 (right O2 sensor,before CAT,CYL 1-3) aging,calibration program jump over
P200C-001 B6/1 (camshaft Hall sensor),no signal [P0340]
P200C-002 B6/1 (camshaft Hall sensor),signal error [P0341]
P200D P0335 [1] L5 (Crankshaft position sensor) ,: No signal [P0335]
P200D P0335 [4] L5 (Crankshaft position sensor) ,: Short circuit Signal wire / Open circuit in wiring [P0335]
P200D P0336 [2] L5 (Crankshaft position sensor) ,: Signal IMPLAUSIBLE [P0336]
P200D Component N15/3 (ETC control module) is faulty.
P200D Component N15/3(ETC control module) is faulty.
P200D G3/4 (Right O2 sensor,before TWC[CAT]) Aging,period too long (P0133)
P200D G3/9 (right O2 sensor,before CAT,CYL 1-3) aging,used too long (P0133)
P200D-001 L5 (crankshaft position sensor),no signal [P0335]
P200D-002 L5 (crankshaft position sensor),signal error [P0336]
P200D-004 L5 (crankshaft position sensor),signal line/wire interrupt cause short [P0335]
P200E P0702 [1] Fault is stored in component N15/3 (ETC control module).: [P0702]
P200E P0702 [128] Fault is stored in component N15/3 (ETC control module).: [P0702]
P200E P0743 [16] Fault is stored in component N15/3 (ETC control module).: [P0743]
P200E P0748 [32] Fault is stored in component N15/3 (ETC control module).: [P0748]
P200E P0748 [64] Fault is stored in component N15/3 (ETC control module).: [P0748]
P200E P0753 [2] Fault is stored in component N15/3 (ETC control module).: [P0753]
P200E P0758 [4] Fault is stored in component N15/3 (ETC control module).: [P0758]
P200E P0763 [8] Fault is stored in component N15/3 (ETC control module).: [P0763]
P200E G3/13 (right O2 sensor,after CAT,CYL 1-3) no special status variation
P200E G3/6 (Right O2 sensor,after TWC[CAT])
P200E-001 component N15/3 (EGS controller) trouble stored.[P0702]
P200E-002 component N15/3 (EGS controller) trouble stored.[P0753]
P200E-004 component N15/3 (EGS controller) trouble stored.[P0758]
P200E-008 component N15/3 (EGS controller) trouble stored.[P0763]
P200E-016 component N15/3 (EGS controller) trouble stored.[P0743]
P200E-032 component N15/3 (EGS controller) trouble stored.[P0748]
P200E-064 component N15/3 (EGS controller) trouble stored.[P0748]
P200E-128 component N15/3 (EGS controller) trouble stored.[P0702]
P200F P0700 [16] Fault is stored in component N15/3 (ETC control module).: [P0700]
P200F P0700 [8] Fault is stored in component N15/3 (ETC control module).: [P0700]
P200F P0705 [2] Fault is stored in component N15/3 (ETC control module).: [P0705]
P200F P0715 [1] Fault is stored in component N15/3 (ETC control module).: [P0715]
P200F P0720 [4] Fault is stored in component N15/3 (ETC control module).: [P0720]
P200F P0730 [64] Fault is stored in component N15/3 (ETC control module).: [P0730]
P200F P0740 [32] Fault is stored in component N15/3 (ETC control module).: [P0740]
P200F G3/4 (Right O2 sensor,before TWC[CAT])(P0130)
P200F G3/9 (right O2 sensor,before CAT,CYL 1-3),too small voltage up (P0130)
P200F-001 component N15/3 (EGS controller) trouble stored.[P0715]
P200F-002 component N15/3 (EGS controller) trouble stored.[P0705]
P200F-004 component N15/3 (EGS controller) trouble stored.[P0720]
P200F-008 component N15/3 (EGS controller) trouble stored.[P0700]
P200F-016 component N15/3 (EGS controller) trouble stored.[P0700]
P200F-032 component N15/3 (EGS controller) trouble stored.[P0740]
P200F-064 component N15/3 (EGS controller) trouble stored.[P0730]
P2010 P0201 [4] Y62y1 (Fuel injector cylinder 1) ,: Open circuit in wiring [P0201]
P2010 P0261 [2] Y62y1 (Fuel injector cylinder 1) ,: Short circuit to ground [P0261]
P2010 P0262 [1] Y62y1 (Fuel injector cylinder 1) ,: Short circuit to positive [P0262]
P2010 Control module N15/3(ETC control module is not coded.
P2010 G3/13 (right O2 sensor,after CAT,CYL 1-3),electrical malfunction (P0136)
P2010 G3/6 (Right O2 sensor,after TWC[CAT])(P0136)
P2010-001 Y62/y1 (cylinder 1 fuel injector),positive short [P0262]
P2010-002 Y62/y1 (cylinder 1 fuel injector),overload short [P0261]
P2010-003 Y62/y1 (cylinder 1 fuel injector),wire interrupt [P0201]
P2011 P0203 [4] Y62y3 (Fuel injector cylinder 3) ,: Open circuit in wiring [P0203]
P2011 P0267 [2] Y62y3 (Fuel injector cylinder 3) ,: Short circuit to ground [P0267]
P2011 P0268 [1] Y62y3 (Fuel injector cylinder 3) ,: Short circuit to positive [P0268]
P2011 A16/1 (Knock sensor 1,right)
P2011 check B2/6 (left hot film air flow meter).Implausible
P2011 check B2/6 (left hot film air flow meter).Signal voltage too high.
P2011 check B2/6 (left hot film air flow meter).Signal voltage too low.
P2011 check B2/6 (right hot film air flow meter).Signal voltage too high.
P2011 check B2/6 (right hot film air flow meter).Signal voltage too low.
P2011 check B2/7 (right hot film air flow meter).Implausible
P2011 check hot film air flow meter.Creditability error
P2011 The coding of the control unit N15/3 (ETC control module) is impermissible.
P2011 The coding of the control unit N15/3(ETC control module) is impermissible.
P2011-001 Y62/y3 (cylinder 3 fuel injector),positive short [P0268]
P2011-002 Y62/y3 (cylinder 3 fuel injector),overload short [P0267]
P2011-003 Y62/y3 (cylinder 3 fuel injector),wire interrupt [P0203]
P2012 P0204 [4] Y62y4 (Fuel injector cylinder 4) ,: Open circuit in wiring [P0204]
P2012 P0270 [2] Y62y4 (Fuel injector cylinder 4) ,: Short circuit to ground [P0270]
P2012 P0271 [1] Y62y4 (Fuel injector cylinder 4) ,: Short circuit to positive [P0271]
P2012 check B17 (intake air temperature sensor).Signal voltage too high.
P2012 check B17 (intake air temperature sensor).Signal voltage too low.
P2012 The checksum of the standard software status for component N15/3 (ETC control module) is missing or is not entered.
P2012 Y58/4 (Activated charcoal canister shut-off valve)(P0446)
P2012 Y58/4 (canister lock valve)(work link)(P0446)
P2012-001 Y62/y4 (cylinder 4 fuel injector),positive short [P0271]
P2012-002 Y62/y4 (cylinder 4 fuel injector),overload short [P0270]
P2012-003 Y62/y4 (cylinder 4 fuel injector),wire interrupt [P0204]
P2013 P0202 [4] Y62y2 (Fuel injector cylinder 2) ,: Open circuit in wiring [P0202]
P2013 P0264 [2] Y62y2 (Fuel injector cylinder 2) ,: Short circuit to ground [P0264]
P2013 P0265 [1] Y62y2 (Fuel injector cylinder 2) ,: Short circuit to positive [P0265]
P2013 check B28 (pressure sensor).Intake air pressure/atmosphere pressure implausible
P2013 check B28 (pressure sensor).Signal voltage too high.
P2013 check B28 (pressure sensor).Signal voltage too low.
P2013 check B28/5 (pressure sensor behind the air cleaner).Atmosphere pressure value implausible.
P2013 check B28/5 (pressure sensor behind the air cleaner).Intake air manifold pressure signal too large.
P2013 check B28/5 (pressure sensor behind the air cleaner).Intake air manifold pressure signal too small.
P2013 Component N15/3(ETC control module) is faulty.
P2013 EGR system severe leaks (P0455)
P2013 Major leak in purge system (P0455)
P2013 N3/9 (controller CDI)/atmosphere pressure sensor.Signal voltage too high.
P2013 N3/9 (controller CDI)/atmosphere pressure sensor.Signal voltage too low.
P2013-001 Y62/y2 (cylinder 2 fuel injector),positive short [P0265]
P2013-002 Y62/y2 (cylinder 2 fuel injector),overload short [P0264]
P2013-003 Y62/y2 (cylinder 2 fuel injector),wire interrupt [P0202]
P2014 P0010 [1] Y49 (Adjustable camshaft timing solenoid) ,: Short circuit to positive [P0010]
P2014 P0010 [2] Y49 (Adjustable camshaft timing solenoid) ,: Short circuit to ground [P0010]
P2014 P0010 [4] Y49 (Adjustable camshaft timing solenoid) ,: Open circuit in wiring [P0010]
P2014 P0010 [8] Y49 (Adjustable camshaft timing solenoid) ,: Mechanical fault [P0010]
P2014 check B19/3 (left catalyzer temperature sensor after supercharger).Signal voltage too high.
P2014 check B19/3 (left catalyzer temperature sensor after supercharger).Signal voltage too low.
P2014 check B19/4 (right catalyzer temperature sensor,after supercharger).Signal voltage too high.
P2014 check B19/4 (right catalyzer temperature sensor,after supercharger).Signal voltage too low.
P2014 check B19/5 (left catalyzer temperature sensor before supercharger).Signal voltage too low.
P2014 check B19/5 (left catalyzer temperature sensor,before bottom catalyzer).Signal voltage too high.
P2014 check B19/6 (right catalyzer temperature sensor,before bottom catalyzer).Signal voltage too high.
P2014 check B19/6 (right catalyzer temperature sensor,before bottom catalyzer).Signal voltage too low.
P2014 EGR system slight leaks (P0442)
P2014 Purge control system has slight leak (P0442)
P2014-001 Y49 (camshaft control device regulation solenoid valve),positive short [P0010]
P2014-002 Y49 (camshaft control device regulation solenoid valve),overload short [P0010]
P2014-004 Y49 (camshaft control device regulation solenoid valve),wire interrupt [P0010]
P2014-008 Y49 (camshaft control device regulation solenoid valve),mechanical malfunction [P0010]
P2015 check start control.Circuit open
P2015 check start control.Short
P2015 check start control.short to ground
P2015 EGR system leaks (work link)(P0440)
P2015 Purge control system has leak (function chain)(P0440)
P2015-001 S40/3 (clutch pedal switch),trouble
P2016 P0443 [8] Y58/1 (Purge control valve) ,: Valve jamming/ stiff Status: OPEN [P0443]
P2016 P0444 [4] Y58/1 (Purge control valve) ,: Open circuit in wiring [P0444]
P2016 P0445 [1] Y58/1 (Purge control valve) ,: Short circuit to positive [P0445]
P2016 P0445 [2] Y58/1 (Purge control valve) ,: Short circuit to ground [P0445]
P2016 check Y76y1 (cylinder 1 fuel injector).Short
P2016 check Y76y2 (cylinder 2 fuel injector).Short
P2016 check Y76y3 (cylinder 3 fuel injector).Short
P2016 check Y76y4 (cylinder 4 fuel injector).Short
P2016 check Y76y5 (cylinder 5 fuel injector).Short
P2016 check Y76y6 (cylinder 6 fuel injector).Short
P2016 check Y76y7 (cylinder 7 fuel injector).Short
P2016 check Y76y8 (cylinder 8 fuel injector).Short
P2016 cylinder 1-3 mixture self regulation reach limit (part load)(P0170)
P2016 Self-adaptation of mixture formation for right bank of cylinders is at limit value (at part load).(P0170)
P2016-001 Y58/1 (EGR device switch-over valve),positive short [P0445]
P2016-002 Y58/1 (EGR device switch-over valve),overload short [P0445]
P2016-004 Y58/1 (EGR device switch-over valve),wire interrupt [P0444]
P2016-008 Y58/1 (EGR device switch-over valve),valve stick condition pen [P0443]
P2017 – [1] K40k1 (Fuel pump relay) / K27 (Fuel pump relay) / N10/2kA (Fuel pump relay) ,: Short circuit to positive
P2017 – [2] K40k1 (Fuel pump relay) / K27 (Fuel pump relay) / N10/2kA (Fuel pump relay) ,: Short circuit to ground
P2017 – [4] K40k1 (Fuel pump relay) / K27 (Fuel pump relay) / N10/2kA (Fuel pump relay) ,: Open circuit in wiring
P2017 check Y76y1 (cylinder 1 fuel injector).Fault
P2017 check Y76y2 (cylinder 2 fuel injector).Fault
P2017 check Y76y3 (cylinder 3 fuel injector).Fault
P2017 check Y76y4 (cylinder 4 fuel injector).Fault
P2017 check Y76y5 (cylinder 5 fuel injector).Fault
P2017 check Y76y6 (cylinder 6 fuel injector).Fault
P2017 check Y76y7 (cylinder 7 fuel injector).Fault
P2017 check Y76y8 (cylinder 8 fuel injector).Fault
P2017 cylinder 1-3 mixture self regulation reach limit (idle)(P0170)
P2017 Self-adaptation of mixture formation for right bank of cylinders is at limit value (at idle speed).(P0170)
P2017-001 K40k1 (fuel pump relay)/K27 (fuel pump relay)/N10/2kA (fuel pump relay),positive short
P2017-002 K40k1 (fuel pump relay)/K27 (fuel pump relay)/N10/2kA (fuel pump relay),overload short
P2017-004 K40k1 (fuel pump relay)/K27 (fuel pump relay)/N10/2kA (fuel pump relay),wire interrupt
P2018 P0413 [4] Y32 (Air pump switchover valve) ,: Open circuit in wiring [P0413]
P2018 P0414 [1] Y32 (Air pump switchover valve) ,: Short circuit to positive [P0414]
P2018 P0414 [2] Y32 (Air pump switchover valve) ,: Short circuit to ground [P0414]
P2018 check M3 (fuel pump).Circuit open
P2018 check M3 (fuel pump).Short
P2018 check M3 (fuel pump).Short to ground
P2018 cylinder 1-3 mixture self regulation reach limit (between idle and part load)
P2018 Self-adaptation of mixture formation for right bank of cylinders is at limit value (between idle speed and part load).(P0170)
P2018-001 Y32 (air pump switch-over valve),positive short [P0414]
P2018-002 Y32 (air pump switch-over valve),overload short [P0414]
P2018-004 Y32 (air pump switch-over valve),wire interrupt [P0413]
P2019 P0410 [1] K40/4k3 (Air pump relay) , N10/1kO (Air pump relay) ,: Short circuit to positive [P0410]
P2019 P0410 [2] K40/4k3 (Air pump relay) , N10/1kO (Air pump relay) ,: Short circuit to ground [P0410]
P2019 check Y74 (pressure regulation valve).Current in pressure regulation valve too small
P2019 check Y74 (pressure regulation valve).Current pressure regulation valve too large
P2019 check Y74 (pressure regulation valve).Regulation error
P2019 check Y94 (flux regulation valve).Current too large
P2019 check Y94 (flux regulation valve).Current value too small
P2019 check Y94 (flux regulation valve).Regulation error too large
P2019 Power output limited because of excessively high temperature of coolant
P2019 power restricted by high refrigerant temperature
P2019-001 K40/4k3 (air pump relay),N10/1KO (air pump relay),positive short [P0410]
P2019-002 K40/4k3 (air pump relay),N10/1KO (air pump relay),overload short [P0410]
P201A P0335 [1] Sensor rotor adaptation ,: Tooth detection is faulty. / Mechanical fault [P0335]
P201A P0335 [2] Sensor rotor adaptation ,: Fault Adaptation [P0335]
P201A B6/1 (Camshaft Hall sensor)(P0341)
P201A B6/3 (camshaft Hall sensor,right cylinder bank)(P0341)
P201A-001 wheel adaptive sensor,gear gap error/mechanical malfunction [P0335]
P201A-002 wheel adaptive sensor,error regulation [P0335]
P201B – [128] : Misfiring of cylinder 2, damages TWC Fuel deficiency
P201B – [16] : Misfiring of cylinder 1, damages TWC Fuel deficiency
P201B – [32] : Misfiring of cylinder 3, damages TWC Fuel deficiency
P201B – [64] : Misfiring of cylinder 4, damages TWC Fuel deficiency
P201B P0301 [1] : Misfiring of cylinder 1, damages TWC [P0301]
P201B P0302 [8] : Misfiring of cylinder 2, damages TWC [P0302]
P201B P0303 [2] : Misfiring of cylinder 3, damages TWC [P0303]
P201B P0304 [4] : Misfiring of cylinder 4, damages TWC [P0304]
P201B component N3/10 (ME controller) supply voltage (P0560)
P201B Voltage supply of component N3/10 (ME-SFI control module)(P0560)
P201B-001 cylinder 1 interrupt device,CAT malfunction [P0301]
P201B-002 cylinder 3 interrupt device,CAT malfunction [P0303]
P201B-004 cylinder 4 interrupt device,CAT malfunction [P0304]
P201B-008 cylinder 2 interrupt device,CAT malfunction [P0302]
P201B-016 cylinder 1 interrupt device,CAT malfunction fuel insufficient
P201B-032 cylinder 3 interrupt device,CAT malfunction fuel insufficient
P201B-064 cylinder 4 interrupt device,CAT malfunction fuel insufficient
P201B-128 cylinder 2 interrupt device,CAT malfunction fuel insufficient
P201C – [128] : Misfiring of cylinder 2 Fuel deficiency
P201C – [16] : Misfiring of cylinder 1 Fuel deficiency
P201C – [32] : Misfiring of cylinder 3 Fuel deficiency
P201C – [64] : Misfiring of cylinder 4 Fuel deficiency
P201C P0301 [1] : Misfiring of cylinder 1 [P0301]
P201C P0302 [8] : Misfiring of cylinder 2 [P0302]
P201C P0303 [2] : Misfiring of cylinder 3 [P0303]
P201C P0304 [4] : Misfiring of cylinder 4 [P0304]
P201C B4/3 (fuel tank pressure sensor),electrical malfunction (P0450)
P201C Misfiring at several cylinders [P0300]
P201C-001 cylinder 1 interrupt device [P0301]
P201C-002 cylinder 3 interrupt device [P0303]
P201C-004 cylinder 4 interrupt device [P0304]
P201C-008 cylinder 2 interrupt device [P0302]
P201C-016 cylinder 1 interrupt device fuel insufficient
P201C-032 cylinder 3 interrupt device fuel insufficient
P201C-064 cylinder 4 interrupt device fuel insufficient
P201C-128 cylinder 2 interrupt device fuel insufficient
P201D P0171 [2] Selfadaptation of mixture formation ,: The mixture is too lean in the part load range. [P0171]
P201D P0171 [8] Selfadaptation of mixture formation ,: Mixture is too lean at idle speed. [P0171]
P201D P0172 [1] Selfadaptation of mixture formation ,: The mixture is too rich in the part load range. [P0172]
P201D P0172 [4] Selfadaptation of mixture formation ,: Mixture is too rich at idle speed. [P0172]
P201D Y62y1 (cylinder 1 injector)(P0201)
P201D Y62y1 (Fuel injector cylinder 1)(P0201)
P201D-001 mixture formation unit adaptation,part load mixture too rich.[P0172]
P201D-002 mixture formation unit adaptation,part load mixture too lean.[P0171]
P201D-004 mixture formation unit adaptation,idle mixture too rich.[P0172]
P201D-008 mixture formation unit adaptation,idle mixture too lean.[P0171]
P201E Y62y5 (cylinder 1 injector)(P0205)
P201E Y62y5 (Fuel injector cylinder 5)(P0205)
P201E-001 CAT effect too small [P0420]
P201F – [1] B40 (Oil sensor (oil level, temperature and quality)) ,: Electrical fault
P201F – [16] B40 (Oil sensor (oil level, temperature and quality)) ,: Oil quality is implausible.
P201F – [2] B40 (Oil sensor (oil level, temperature and quality)) ,: Oil temperature
P201F – [4] B40 (Oil sensor (oil level, temperature and quality)) ,: Oil quality
P201F – [8] B40 (Oil sensor (oil level, temperature and quality)) ,: Oil level
P201F Y62y3 (cylinder 5 injector)(P0203)
P201F Y62y4 (Fuel injector cylinder 4)(P0204)
P201F-001 B40 (engine oil sensor (engine oil condition,temperature and quality)),electrical malfunction
P201F-002 B40 (engine oil sensor (engine oil condition,temperature and quality)),engine oil temperature
P201F-004 B40 (engine oil sensor (engine oil condition,temperature and quality)),engine oil quality
P201F-008 B40 (engine oil sensor (engine oil condition,temperature and quality)),engine oil condition
P201F-016 B40 (engine oil sensor (engine oil condition,temperature and quality)),engine oil quality error
P2020 – [1] M4/3 (engine/AC electric suction fan) ,: Short circuit to positive
P2020 – [2] M4/3 (engine/AC electric suction fan) ,: Short circuit to ground / Open circuit in wiring
P2020 check fuel rail pressure:B4/6 (fuel rail pressure sensor) racing test.
P2020 check fuel rail pressure:Y74 (pressure regulation valve) racing test.
P2020 check fuel rail pressure:Y94 (flux regulation valve) racing test.
P2020 check Y74 (pressure regulation valve).Short
P2020 check Y94 (flux regulation valve).Short
P2020 Y62y2 (Fuel injector cylinder 2)(P0202)
P2020 Y62y6 (cylinder 5 injector)(P0206)
P2020-001 M4/3 (engine/A/C electronic intake air device),positive short
P2020-002 M4/3 (engine/A/C electronic intake air device),overload/wire open cause short
P2021 – [1] Relays Starter ,: Short circuit to positive
P2021 – [2] Relays Starter ,: Short circuit to ground / Open circuit in wiring
P2021 check Y74 (pressure regulation valve).Current in pressure regulation valve too large
P2021 check Y74 (pressure regulation valve).Current in pressure regulation valve too small.Fuel rail pressure too high.
P2021 check Y74 (pressure regulation valve).Current/fuel rail pressure too large
P2021 check Y74 (pressure regulation valve).Current/fuel rail pressure too small
P2021 check Y74 (pressure regulation valve).Fuel rail pressure too small.
P2021 check Y74 (pressure regulation valve).Maximal pressure will be rewrite.
P2021 check Y74 (pressure regulation valve).Negative regulation error
P2021 check Y74 (pressure regulation valve).Regulation error too large
P2021 Y62y2 (cylinder 5 injector)(P0202)
P2021 Y62y6 (Fuel injector cylinder 6)(P0206)
P2021-001 starter relay,positive short
P2021-002 starter relay,overload/wire open cause short
P2022 P0135 [1] Heating of component G3/2 (O2 sensor upstream TWC) ,: Short circuit to positive [P0135]
P2022 P0135 [2] Heating of component G3/2 (O2 sensor upstream TWC) ,: Short circuit to ground [P0135]
P2022 P0135 [4] Heating of component G3/2 (O2 sensor upstream TWC) ,: Open circuit in wiring [P0135]
P2022 P0135 [8] Heating of component G3/2 (O2 sensor upstream TWC) ,: Heating capacity is too low. [P0135]
P2022 check fuel injector.Cylinder 1 misfire
P2022 check fuel injector.Cylinder 2 misfire
P2022 check fuel injector.Cylinder 3 misfire
P2022 check fuel injector.Cylinder 4 misfire
P2022 check fuel injector.Cylinder 5 misfire
P2022 check fuel injector.Cylinder 6 misfire
P2022 check fuel injector.Cylinder 7 misfire
P2022 check fuel injector.Cylinder 8 misfire
P2022 Y62y3 (Fuel injector cylinder 3)(P0203)
P2022 Y62y4 (cylinder 5 injector)(P0204)
P2022-001 component G3/2 (before CAT O2 sensor) heating device,positive short [P0135]
P2022-002 component G3/2 (before CAT O2 sensor) heating device,overload short [P0135]
P2022-004 component G3/2 (before CAT O2 sensor) heating device,wire interrupt [P0135]
P2022-008 component G3/2 (O2 sensor before CAT) heating device,heating power too small.[P0135]
P2023 P0141 [1] Heating of component G3/1 (O2 sensor downstream TWC) ,: Short circuit to positive [P0141]
P2023 P0141 [2] Heating of component G3/1 (O2 sensor downstream TWC) ,: Short circuit to ground [P0141]
P2023 P0141 [4] Heating of component G3/1 (O2 sensor downstream TWC) ,: Open circuit in wiring [P0141]
P2023 P0141 [8] Heating of component G3/1 (O2 sensor downstream TWC) ,: Heating capacity is too low. [P0141]
P2023 check Y83 (intake air manifold turnoff switch valve).Circuit open
P2023 check Y83 (intake air manifold turnoff switch valve).It is OFF when left intake air manifold is closed.
P2023 check Y83 (intake air manifold turnoff switch valve).It is OFF when right intake air manifold is closed.
P2023 check Y83 (intake air manifold turnoff switch valve).It is ON when left intake air manifold is closed.
P2023 check Y83 (intake air manifold turnoff switch valve).It is ON when right intake air manifold is closed.
P2023 check Y83 (intake air manifold turnoff switch valve).Short
P2023 check Y83 (intake air manifold turnoff switch valve).Short to ground
P2023 K40/7kN (air pump relay)(P0410)
P2023-001 component G3/1 (O2 sensor before CAT) heating device,positive short [P0141]
P2023-002 component G3/1 (O2 sensor before CAT) heating device,overload short [P0141]
P2023-004 component G3/1 (O2 sensor before CAT) heating device,wire interrupt [P0141]
P2023-008 component G3/2 (O2 sensor before CAT) heating device,heating power too small.[P0141]
P2024 P0106 [4] B28 (Pressure sensor) ,: Signal B28 (Pressure sensor) not equal to signal B18 (Altitude pressure sensor) when engine not running [P0106]
P2024 P0107 [2] B28 (Pressure sensor) ,: Short circuit to ground [P0107]
P2024 P0108 [1] B28 (Pressure sensor) ,: Short circuit to positive / Open circuit in wiring [P0108]
P2024 check Y27/10 (right exhaust gas recirculation regulator) regulator fault (via ground key).
P2024 check Y27/10 (right exhaust gas recirculation regulator).Circuit open
P2024 check Y27/10 (right exhaust gas recirculation regulator).Short
P2024 check Y27/10 (right exhaust gas recirculation regulator).Short to ground
P2024 check Y27/9 (left exhaust gas recirculation regulator) regulator fault (via ground key).
P2024 check Y27/9 (left exhaust gas recirculation regulator).Circuit open
P2024 check Y27/9 (left exhaust gas recirculation regulator).Short
P2024 check Y27/9 (left exhaust gas recirculation regulator).Short to ground
P2024 Y32 (Air pump switchover valve)(P0412)
P2024 Y32/2 (air pump switch-over valve,right cylinder bank)(P0412)
P2024-001 B28 (pressure sensor),positive short/wire open cause short [P0108]
P2024-002 B28 (pressure sensor),overload short [P0107]
P2024-004 B28 (pressure sensor),engine inactive B28 (pressure sensor) signal not equal to B18 (high pressure sensor) signal [P0106]
P2025 P0351 [1] : T1/1 (ignition coil cylinder 1) Combustion period , Readout too small [P0351]
P2025 P0351 [2] : T1/1 (ignition coil cylinder 1) Primary voltage [P0351]
P2025 P0352 [128] : T1/2 (ignition coil cylinder 2) Primary voltage [P0352]
P2025 P0352 [64] : T1/2 (ignition coil cylinder 2) Combustion period , Readout too small [P0352]
P2025 P0353 [4] : T1/3 (ignition coil cylinder 3) Combustion period , Readout too small [P0353]
P2025 P0353 [8] : T1/3 (ignition coil cylinder 3) Primary voltage [P0353]
P2025 P0354 [16] : T1/4 (ignition coil cylinder 4) Combustion period , Readout too small [P0354]
P2025 P0354 [32] : T1/4 (ignition coil cylinder 4) Primary voltage [P0354]
P2025 check M16/5 (throttle valve regulator).Circuit open
P2025 check M16/5 (throttle valve regulator).M16/5 (throttle valve regulator) regulator fault (via ground key).
P2025 check M16/5 (throttle valve regulator).Short
P2025 check M16/5 (throttle valve regulator).Short to ground
P2025 Y58/4 (Activated charcoal canister shut-off valve)(P0446)
P2025 Y58/4 (canister closedown valve)(P0446)
P2025-001 T1/1 (cylinder 1 ignition coil) ignition duration,value too small [P0351]
P2025-002 T1/1 (cylinder 1 ignition coil) primary voltage [P0351]
P2025-004 T1/3 (cylinder 3 ignition coil) ignition duration,value too small [P0353]
P2025-008 T1/3 (cylinder 3 ignition coil) primary voltage [P0353]
P2025-016 T1/4 (cylinder 4 ignition coil) ignition duration,value too small [P0354]
P2025-032 T1/4 (cylinder 4 ignition coil) primary voltage [P0354]
P2025-064 T1/2 (cylinder 2 ignition coil) ignition duration,value too small [P0352]
P2025-128 T1/2 (cylinder 2 ignition coil) primary voltage [P0352]
P2026 P0600 [1] CAN message from control module N15/3 (ETC control module) ,: CAN signal faulty [P0600]
P2026 P0600 [16] CAN message from control module N15/3 (ETC control module) ,: CAN signal interruption [P0600]
P2026 P0600 [2] CAN message from control module N15/3 (ETC control module) ,: CAN signal faulty [P0600]
P2026 P0600 [4] CAN message from control module N15/3 (ETC control module) ,: CAN signal faulty ( Torque ) [P0600]
P2026 P0600 [8] CAN message from control module N15/3 (ETC control module) ,: CAN signal faulty [P0600]
P2026 exhaust gas recirculation negative regulation deviation/exhaust gas recirculation rate too high.
P2026 exhaust gas recirculation positive regulation deviation/exhaust gas recirculation rate too low.
P2026 Y58/1 (EGR switch-over valve)(P0443)
P2026 Y58/1 (Purge control valve)(P0443)
P2026-001 CAN BUS signal from N15/3 (EGS controller) controller,CAN BUS signal error [P0600]
P2026-002 CAN BUS signal from N15/3 (EGS controller) controller,CAN BUS signal error [P0600]
P2026-004 CAN BUS signal from N15/3 (EGS controller) controller,CAN BUS signal error (torque) [P0600]
P2026-008 CAN BUS signal from N15/3 (EGS controller) controller,CAN BUS signal error [P0600]
P2026-016 CAN BUS signal from N15/3 (EGS controller) controller,CAN BUS signal interrupt [P0600]
P2027 – [1] CAN message from control module N47-5 (ESP, SPS and BAS control module) ,: CAN signal faulty
P2027 – [2] CAN message from control module N47-5 (ESP, SPS and BAS control module) ,: CAN signal faulty
P2027 – [32] CAN message from control module N47-5 (ESP, SPS and BAS control module) ,: CAN signal faulty ( Stop lamp switch )
P2027 – [4] CAN message from control module N47-5 (ESP, SPS and BAS control module) ,: CAN signal faulty ( Torque )
P2027 – [64] CAN message from control module N47-5 (ESP, SPS and BAS control module) ,: CAN signal faulty ( Stop lamp switch )
P2027 – [8] CAN message from control module N47-5 (ESP, SPS and BAS control module) ,: CAN signal faulty
P2027 P0600 [16] CAN message from control module N47-5 (ESP, SPS and BAS control module) ,: CAN signal interruption [P0600]
P2027 Y100 (left boost regulator) circuit open
P2027 Y100 (left boost regulator) regulator fault (via ground key).
P2027 Y100 (left boost regulator) short
P2027 Y100 (left boost regulator) short to ground
P2027 Y100/1 (right boost regulator) circuit open
P2027 Y100/1 (right boost regulator) regulator fault (via ground key).
P2027 Y100/1 (right boost regulator) short
P2027 Y100/1 (right boost regulator) short to ground
P2027 Y31/1 (EGR vacuum transducer)(P0403)
P2027-001 CAN BUS signal from N47-5 (ESP,PML and BAS controller) controller,CAN BUS signal error
P2027-002 CAN BUS signal from N47-5 (ESP,PML and BAS controller) controller,CAN BUS signal error
P2027-004 CAN BUS signal from N47-5 (ESP,PML and BAS controller) controller,CAN BUS signal error
P2027-008 CAN BUS signal from N47-5 (ESP,PML and BAS controller) controller,CAN BUS signal error (torque)
P2027-016 CAN BUS signal from N47-5 (ESP,PML and BAS controller) controller,CAN BUS signal interrupt [P0600]
P2027-032 CAN BUS signal from N47-5 (ESP,PML and BAS controller) controller,CAN BUS signal from (brake light switch)
P2027-064 CAN BUS signal from N47-5 (ESP,PML and BAS controller) controller,CAN BUS signal from (brake light switch)
P2028 P0562 [1] : Battery voltage too low [P0562]
P2028 P0563 [2] : Battery voltage too high / IMPLAUSIBLE [P0563]
P2028 boost regulator negative regulation deviation/boost pressure too high.
P2028 boost regulator positive regulation deviation/boost pressure too low.
P2028 the fill-in coefficient of this component exeeded
P2028 Y49/2 (camshaft adjusting valve,right cylinder bank)(P0340)
P2028-001 battery voltage too low [P0562]
P2028-002 battery voltage too high/error [P0563]
P2029 check S40/4 (button type switch TPM with variable speed limit).Closed
P2029 check S40/4 (button type switch TPM with variable speed limit).Negative acceleration limit
P2029 check S40/4 (button type switch TPM with variable speed limit).Positive acceleration limit
P2029 right cylinder bank camshaft adjustment (work link)(P0340)
P2029-001 engine RPM signal,error
P202A P0171 [8] : Selfadaptation of mixture formation at rich stop [P0171]
P202A P0172 [4] : Selfadaptation of mixture formation at lean stop [P0172]
P202A left cylinder bank camshaft adjustment (work link)(P0340)
P202A-004 mixture formation unit adaptation lean [P0172]
P202A-008 mixture formation unit adaptation too rich [P0171]
P202B – [16] CAN message from control module ESP ,: Vehicle speed signal IMPLAUSIBLE
P202B – [2] CAN message from control module ESP ,: Vehicle speed signal IMPLAUSIBLE
P202B – [4] CAN message from control module ESP ,: Vehicle speed signal IMPLAUSIBLE
P202B – [8] CAN message from control module ESP ,: Vehicle speed signal IMPLAUSIBLE
P202B P0500 [1] CAN message from control module ESP ,: Vehicle speed signal IMPLAUSIBLE [P0500]
P202B idle regulation error (P0507)
P202B Idle speed control implausible (P0507)
P202B-001 CAN BUS signal from ESP controller,speed signal error [P0500]
P202B-002 CAN BUS signal from ESP controller,speed signal error
P202B-004 CAN BUS signal from ESP controller,speed signal error
P202B-008 CAN BUS signal from ESP controller,speed signal error
P202B-016 CAN BUS signal from ESP controller,speed signal error
P202C – [1] CAN message from control module EIS ,: CAN signal interruption
P202C – [2] CAN message from control module EIS ,: CAN signal faulty
P202C – [4] CAN message from control module EIS ,: CAN signal faulty
P202C – [8] CAN message from control module EIS ,: CAN signal interruption Drive authorization
P202C Coolant thermostat (P0115)
P202C refrigerant temperature regulator (P0115)
P202C-001 CAN BUS signal from EIS controller,CAN BUS signal interrupt
P202C-002 signal from EIS controller CAN BUS,CAN BUS signal error
P202C-004 CAN BUS signal from EIS controller,CAN BUS signal error
P202C-008 CAN BUS signal from EIS controller,CAN BUS signal interrupt drive authority
P202D – [1] CAN message from control module Instrument cluster ,: CAN signal interruption
P202D – [2] CAN message from control module Instrument cluster ,: Fuel tank level IMPLAUSIBLE
P202D – [4] CAN message from control module Instrument cluster ,: Ambient temperature IMPLAUSIBLE
P202D B11/4 (Coolant temperature sensor),Plausibility (P0115)
P202D B11/4 (refrigerant temperature sensor),reliability (P0115)
P202D-001 CAN BUS signal from combination instrument controller,CAN BUS signal interrupt
P202D-002 CAN BUS signal from combination instrument controller,fuel tank charging condition error
P202D-004 CAN BUS signal from combination instrument controller,outside temperature error
P202E M16/6 (throttle valve actuator)(P0120)
P202E M16/6 (throttle valve regulator)(P0120)
P202E-001 CAN BUS signal from KLA/TAU controller,CAN BUS signal interrupt
P202F P0600 [1] CAN fault ,: 1. CAN controller: CAN bus OFF [P0600]
P202F P0600 [2] CAN fault ,: 2. CAN controller: CAN bus OFF [P0600]
P202F No or incorrect CAN message from control unit N51/2 (ABC control module)(P0600)
P202F no signal or error signal from N51/2 (ABC controller) controller BUS (P0600)
P202F-001 CAN BUS error,1 CAN BUS controller:CAN off [P0600]
P202F-002 CAN BUS error,2 CAN BUS controller:CAN off [P0600]
P2030 – [1] Crash signal ,: IMPLAUSIBLE
P2030 – [2] Crash signal ,: Front crash
P2030 – [4] Crash signal ,: Short circuit to positive
P2030 check heat time control.Communication fault
P2030 check heat time control.N14/2 (pre-heating plug output stage) fault
P2030 check heat time control.Pre-heating indicator fault
P2030 check heat time control.Pre-heating plug short
P2030 No faulty code text
P2030 No or incorrect CAN message from control unit N15/5 (electronic selector lever module control module)(P0600)
P2030 no signal or error signal from N15/5 (electronic shift lever mode controller) controller BUS (P0600)
P2030-001 crash signal,error
P2030-002 crash signal,front crash
P2030-004 Crash signal,positive short
P2031 P0130 [16] G3/2 (O2 sensor upstream TWC) ,: Open circuit [P0130]
P2031 P0130 [32] G3/2 (O2 sensor upstream TWC) ,: Sensor signal in the case of inertia fuel shutoff IMPLAUSIBLE [P0130]
P2031 P0131 [4] G3/2 (O2 sensor upstream TWC) ,: Short circuit to ground [P0131]
P2031 P0132 [8] G3/2 (O2 sensor upstream TWC) ,: Short circuit to positive [P0132]
P2031 P0133 [2] G3/2 (O2 sensor upstream TWC) ,: Aging, period too long [P0133]
P2031 cylinder 1 pre-heating plug
P2031 cylinder 2 pre-heating plug
P2031 cylinder 3 pre-heating plug
P2031 cylinder 4 pre-heating plug
P2031 cylinder 5 pre-heating plug
P2031 cylinder 6 pre-heating plug
P2031 cylinder 7 pre-heating plug
P2031 cylinder 8 pre-heating plug
P2031 Exhaust Gas Temperature Sensor Circuit (Bank 1 Sensor 2)
P2031 No faulty code text
P2031 No or incorrect CAN message from control unit N80 (Jacket tube module)(P0600)
P2031 no signal or error signal from N15/5 (electronic shift lever mode controller) controller BUS (P0600)
P2031-002 G3/2 (before CAT O2 sensor) aging,used too long [P0133]
P2031-004 G3/2 (before CAT O2 sensor),overload short [P0131]
P2031-008 G3/2 (before CAT O2 sensor),positive short [P0132]
P2031-016 G3/2 (before CAT O2 sensor),interrupt [P0130]
P2031-032 G3/2 (before CAT O2 sensor) at off sensor signal error [P0130]
P2032 P0442 [2] Purge system ,: Minor leakage in system [P0442]
P2032 P0455 [4] Purge system ,: Major leakage in system [P0455]
P2032 P0456 [1] Purge system ,: Very slight leak in system [P0456]
P2032 P0457 [16] Purge system ,: No fuel tank cap (fault detected in driving mode). [P0457]
P2032 P0457 [8] Purge system ,: No fuel filler cap (fault detected in idling speed range). [P0457]
P2032 Exhaust Gas Temperature Sensor Circuit Low (Bank 1 Sensor 2)
P2032 M16/6r1 (Throttle valve actual value potentiometer)(P0120)
P2032 M16/6r1 (throttle valve practical potentiometer)(P0120)
P2032 transmission control 1 EGS fault 1
P2032 transmission control 1 EGS fault 2
P2032 transmission control 1 EGS fault 3
P2032 transmission control 1 EGS fault 4
P2032 transmission control 1 EGS fault 5
P2032 transmission control 1 EGS fault 6
P2032 transmission control 1 EGS fault 7
P2032 transmission control 1 EGS fault 8
P2032-001 EGR,very slight leak [P0456]
P2032-002 EGR,slight leak [P0442]
P2032-004 EGR,severe leak [P0455]
P2032-008 EGR,fuel tank cover lose (idle error identified).[P0457]
P2032-016 EGR,fuel tank cover lose (driving error identified).[P0457]
P2033 P0446 [8] Y58/4 (Activated charcoal canister shut-off valve) ,: Valve jamming/ stiff Status: CLOSED [P0446]
P2033 P0447 [4] Y58/4 (Activated charcoal canister shut-off valve) ,: Open circuit in wiring [P0447]
P2033 P0448 [1] Y58/4 (Activated charcoal canister shut-off valve) ,: Short circuit to positive [P0448]
P2033 P0448 [2] Y58/4 (Activated charcoal canister shut-off valve) ,: Short circuit to ground [P0448]
P2033 Exhaust Gas Temperature Sensor Circuit High (Bank 1 Sensor 2)
P2033 S40/4 (CC switch with variable speed limiter)
P2033 S40/4 (TPM touch switch with variable speed limit)
P2033 transmission control 2 EGS fault 1
P2033 transmission control 2 EGS fault 2
P2033 transmission control 2 EGS fault 3
P2033 transmission control 2 EGS fault 4
P2033 transmission control 2 EGS fault 5
P2033 transmission control 2 EGS fault 6
P2033 transmission control 2 EGS fault 7
P2033 transmission control 2 EGS fault 8
P2033-001 Y58/4 (canister cut-off valve),positive short [P0448]
P2033-002 Y58/4 (canister cut-off valve),overload short [P0448]
P2033-004 Y58/4 (canister cut-off valve),wire open [P0447]
P2033-008 Y58/4 (canister cut-off valve),valve stick condition ff [P0446]
P2034 – [1] Shutoff Cruise control ,: Fault Throttle valve
P2034 – [2] Shutoff Cruise control ,: Fault Stop lamp switch
P2034 – [4] Shutoff Cruise control ,: Pushbutton switch IMPLAUSIBLE
P2034 – [8] Shutoff Cruise control ,: CAN signal faulty Stop lamp switch
P2034 check SRS system.Air bag signal short after UB
P2034 check SRS system.Air bag signal will cause the engine stop.
P2034 L5 (crankshaft position sensor)(P0335)
P2034-001 speed meter interrupt,throttle valve malfunction
P2034-002 speed meter interrupt,brake light switch malfunction
P2034-004 speed meter interrupt,touch switch error
P2034-008 speed meter interrupt,brake light switch CAN BUS signal error
P2035 P0221 [1] N3/10 (ME-SFI control module) , Fault: [P0221]
P2035 P0221 [128] N3/10 (ME-SFI control module) , Fault: [P0221]
P2035 P0221 [2] N3/10 (ME-SFI control module) , Fault: [P0221]
P2035 P0221 [4] N3/10 (ME-SFI control module) , Fault: [P0221]
P2035 P0221 [8] N3/10 (ME-SFI control module) , Fault: [P0221]
P2035 P0226 [16] N3/10 (ME-SFI control module) , Fault: [P0226]
P2035 P0226 [32] N3/10 (ME-SFI control module) , Fault: [P0226]
P2035 P0226 [64] N3/10 (ME-SFI control module) , Fault: [P0226]
P2035 check M4/7 (electric inspiration motor and integrated A/C).Circuit open
P2035 check M4/7 (electric inspiration motor and integrated A/C).Short
P2035 check M4/7 (electric inspiration motor and integrated A/C).Short to ground
P2035 M4/7 (electric inspiration motor and integrated A/C) regulator fault (via ground key).
P2035-001 N3/10 (ME controller),malfunction [P0221]
P2035-002 N3/10 (ME controller),malfunction [P0221]
P2035-004 N3/10 (ME controller),malfunction [P0221]
P2035-008 N3/10 (ME controller),malfunction [P0221]
P2035-016 N3/10 (ME controller),malfunction [P0226]
P2035-032 N3/10 (ME controller),malfunction [P0226]
P2035-064 N3/10 (ME controller),malfunction [P0226]
P2035-128 N3/10 (ME controller),malfunction [P0221]
P2036 P0410 [1] Secondary air injection: malfunction (function chain) ,: Air flow is too low. [P0410]
P2036 check N33/2 (heat controller) producer.
P2036 N33/2 (heat controller) circuit open
P2036 N33/2 (heat controller) regulator fault (via ground key).
P2036 N33/2 (heat controller) short
P2036 N33/2 (heat controller) short to ground
P2036 No or incorrect CAN message from control unit N47-5 (ESP control module)(P0600)
P2036 no signal or error signal from N47-5 (ESP controller) controller BUS (P0600)
P2036-001 intake air device:wrong operation (work link),air flow too small.[P0410]
P2037 P0451 [4] B4/3 (Fuel tank pressure sensor) ,: Plausibility error Signal / Fuel filler cap missing. [P0451]
P2037 P0451 [8] B4/3 (Fuel tank pressure sensor) ,: Plausibility error Signal [P0451]
P2037 P0452 [1] B4/3 (Fuel tank pressure sensor) ,: Short circuit to ground [P0452]
P2037 P0453 [2] B4/3 (Fuel tank pressure sensor) ,: Short circuit to positive / Open circuit in wiring [P0453]
P2037 check radiator shutter/engine mount.Engine mount circuit open
P2037 check radiator shutter/engine mount.Engine mount regulator fault (via ground key)
P2037 check radiator shutter/engine mount.Engine mount short to ground
P2037 check radiator shutter/engine mount.Radiator shutter circuit open
P2037 check radiator shutter/engine mount.Radiator shutter regulator fault (via ground key).
P2037 check radiator shutter/engine mount.Radiator shutter short to ground
P2037 No or incorrect CAN message from control unit N15/3 (ETC control module)(P0600)
P2037 no signal or error signal from N15/3 (EGS controller) controller BUS (P0600)
P2037-001 B4/3 (fuel tank pressure sensor),overload short [P0452]
P2037-002 B4/3 (fuel tank pressure sensor),positive short/wire open [P0453]
P2037-004 B4/3 (fuel tank pressure sensor),signal reliability malfunction/fuel tank cover lose.[P0451]
P2037-008 B4/3 (fuel tank pressure sensor),signal reliability malfunction [P0451]
P2038 P0243 [1] : Charge pressure is too low. [P0243]
P2038 P0243 [2] : Charge pressure is too high. [P0243]
P2038 A16/2 (knock sensor 2,left)
P2038 check M44 (booster air cooler circulation pump).Circuit open
P2038 check M44 (booster air cooler circulation pump).Short
P2038 check M44 (booster air cooler circulation pump).Short to ground
P2038-001 charging pressure too low.[P0243]
P2038-002 charging pressure too high.[P0243]
P2039 – [4] M16/7 (Recirculating air flap actuator) ,: Adaptation Emergency running
P2039 P0243 [1] M16/7 (Recirculating air flap actuator) ,: First initialization [P0243]
P2039 P0243 [2] M16/7 (Recirculating air flap actuator) ,: Position Emergency running [P0243]
P2039 CAN-fault,fault 1
P2039 CAN-fault,fault 2
P2039 check CAN.CAN signal from controller N51/2 (controller ABC) (airmatic) error or interfered
P2039 check CAN.CAN-data bus open
P2039 check CAN.CAN-signal from A1 (instrument cluster) error
P2039 check CAN.CAN-signal N15/5 (electronic shift lever module controller) error
P2039 component B40 (oil condition,temperature and quality) il condition error
P2039 component B40 (oil condition,temperature and quality)oil condition error
P2039 Component B40 (Oil sensor (oil level,temperature and quality)) il level implausible
P2039 Component B40 (Oil sensor (oil level,temperature and quality))oil level implausible
P2039-001 M16/7 (air exchange valve adjustment part),not initialization [P0243]
P2039-002 M16/7 (air exchange valve adjustment part),urgency start position [P0243]
P2039-004 M16/7 (air exchange valve adjustment part),urgency start regulation
P203A – [64] M16/7 (Recirculating air flap actuator) ,: Emergency running position not reached
P203A P0244 [128] M16/7 (Recirculating air flap actuator) ,: Actuation Actuator motor [P0244]
P203A P0244 [16] M16/7 (Recirculating air flap actuator) ,: Comparative error Actual value potentiometer [P0244]
P203A P0244 [32] M16/7 (Recirculating air flap actuator) ,: Recirculating air flap sticking. [P0244]
P203A P0245 [2] M16/7 (Recirculating air flap actuator) ,: Actual value potentiometer 1 The signal voltage is too low. [P0245]
P203A P0245 [8] M16/7 (Recirculating air flap actuator) ,: Actual value potentiometer 2 The signal voltage is too low. [P0245]
P203A P0246 [1] M16/7 (Recirculating air flap actuator) ,: Actual value potentiometer 1 The signal voltage is too high. [P0246]
P203A P0246 [4] M16/7 (Recirculating air flap actuator) ,: Actual value potentiometer 2 The signal voltage is too high. [P0246]
P203A insufficient fuel (P0460)
P203A The fuel tank level is too low.(P0460)